Homemade tripod. Homemade tripod: appointment, step-by-step instructions, tips and recommendations Tripod from remedies

In the previous material I told how to remove the video MK at home and touched on the topic of shooting on the phone. And mentioned that at the beginning of work it is quite possible to do without buying special devices. How to make a tripod for your own hands at home. Read below. A full-fledged tripod from the primary means is such that the angle of inclination, turn, the height of the device, etc. - Create hard, but simple holders and low tripods to make it completely forces.

First, a tripod for a smartphone do it yourself, you need to make it so that you have the "Flight Control Panel" - the monitor screen with the desired buttons. After all, you should configure and continue to control the process.

The second requirement - the device must keep the phone so that there is no accidental fall, shift, etc.

Tripod for phone five minutes

How to make a tripod a tripod for the phone with your hands from the girlfriend - tips for those who have no time. These designs are more like the holders for a smartphone than a full-fledged tripod a full-fledged tripod to do for a long time and not all forces. Examples below in the text.

From jars, one-time glasses, etc.

The easiest way to quickly make a tripod-holder for the phone - cut a one-time cup, a jar from the yoghurt (sour cream and so on.). The photo below is clearly seen how such a device works - you need to make slots and insert the phone into them.

If you make a slot, the diagram will be slightly under the tilt.
For location at a higher point, it is enough to put on something else - on the stack of books, on the can, regiment, etc.

pros - Easy, not expensive, quickly.

Minuses - Not suitable for vertical shooting (from above), for a higher position requires a stand.

Tripod from clutches

Another simple way to make a tripod for your own hands in five minutes to use clothespins. Connect them, as shown in the figure and put your device into the resulting system.

pros Obvious - accessible, almost free, quickly.

Minuses The same as the jars - there is no possibility to remove it - the phone simply will not hold.

Fastening the phone on the bank, bottle, etc.

You can fix the phone on a water bottle with a rubber band, as shown in the photo below. Be sure to fill the bottle with water, otherwise the whole design will not stand.

Tripod for phone at home made of table lamp

If you have a desktop lamp with varying guides, a flexible base is a great option for a tripod. It remains only to attach the phone holder directly to it and your tripod is ready!

pros - You can change the height, slope, etc.

Minus - A more complex design that is not done in a couple of minutes.

How to make a tripod for the phone for vertical filming

A more serious option and you need to work for five minutes. The created design serves me for a long time, without requiring a replacement, no repair. Vertical shooting can be conducted at least on the kitchen table, even on the floor, etc.

You will need a pair of long lines (Wooden wide rails, plinths will also fit, even ceiling - the main thing is that they do not go), couple short and conventional cap cardboard box, for example, shoe. The size should not be small so that the phone can be freely located in any position above the opening.

The length of the rail varies from 50 to 100 cm.

In the lid, do a cruciform hole, 3-5 cm width. The main thing is that the phone can be deployed over this hole in different directions.
Further create a line-boring line with each other. The distance between them should be less than the width of the box for several centimeters. The longer the line, the better - you will be more freedom of action. For fastening, you can use even the usual tape, isolent, tape tape. Or more seriously - to bore with screws.
For shooting frame fasten with something heavy on high horizontal surface Near (above) the place of shooting, and the phone just put in the box above the hole. The box is moving freely - it makes it possible to find the best option for shooting.

For filming cooking, this is a great option, it is enough to fix it on the shelf of the hanging cabinet above the desktop.

pros - Available, in a disassembled form, the design does not take up much space.

Minuses - The height is not regulated, you need to look for a stand for fastening.

Wire tripod

Rigid wire will allow you to make a fairly convenient tripod for the phone. If you wish, you can even change the angle of inclination for shooting. To some extent it reminds "Octopus". This design can be screwed to the legs of the chair, the table, to the tree, etc.

Fastening a smartphone for a tripod for a camera

The holder for the telephone from the stationery clamps - the photo everything speaks for itself. Plus the fact that you can use all the functions of the tripod - the tilt, the rotation of the chamber, the change in the height.

Before attaching the first clothespin, it is necessary to screw the camera fastening so that it does not stick. Otherwise, the clamp will not hold on.

Second clamp set as in the photo. And then use the telephone with a rubber band.

Clamps take large, reliable.

Cardboard phone tripod

There are factory cardboard tripod holders for phones. Why not use the idea itself and do not cut and glue with your own hands an analogue of what is shown in the photo below?

How to make my own tripod for the phone - the topic is infinite, a lot of solutions, use your smelling, golden handles and everything will turn out. Pay more attention to the shooting themselves.

Be sure to check the fastening reliability in order to avoid dropments and breakdowns.
Get the phone holder - a simple device, which in addition to man-made structures will be very by the way. It is not expensive, facilitates work.
Remove a lot from different angles so that when installing there is no shortage in video and photo material.

To get a good picture, it is desirable to fix the camera to get a clear focus, because the hands of a person at a concentration start involuntarily to twitch. A tripod helps to solve the problem that can easily be bought in any specialized store or a department trading in a photo product.

Unprofessional photographers are rarely solved to acquire a special tripod, as it is worth it in general, but is not so often applied. Folk craftsmen invented several options for self-made tripods for the camera. How to make a tripod with your own hands and how to replace a tripod for a camera, you will learn from the materials of this article.

How to make a tripod for a camera?

For the manufacture of a tripod for a camera, one-time razor machines was used as the main material in our case.

You will need:

3 razor machine;
small cutting board;
glue "moment";
2 - 5 cm long screw and 0.5 cm diameter;

Nut;
Ring seal;
drill;
Kuzbass varnish or black enamel.

Making tripod from razor machines

On the board, do you draw a small anosexicated triangle, each of the sides of which is more on the half astimeter than the length of the machine blades. Drill in the very center of the triangle make a hole.

Cut the triangular detail, screw the screw in the hole.

Paint the item black, we stick the razors on the sides.

How to fix the camera on the tripod?

We put the sealing ring on the screw and screw the nut. Fresh a camera on the homemade tripod in the same way as the factory product.

Homemade tripod can serve and for attaching a compact video camera.

For lady or girls, you can make a flirty pink tripod, using razor machines designed for women.

As an attachment for the camera, creative masters offer to use healthy items that are almost in every home.

The ideas of creating homemade tripods:

From desktop vice;

From a plastic bottle filled with wet sand or water;

From the cropped dense tennis ball;

From the stack of stacks fasten together video tapes, books or from a solid box.

In emergency cases, you can use any smooth horizontal surface: the fence, high funeral, etc. All this will help avoid trembling a camera or camcorder and make high-quality pictures or a good film organic.

How to make a photochative from the bottle

Being a business trip to prepare a photo report on the results of work. But it is not enough, the premises of a large size, natural lighting lacks, there is no artificial and will not, and the flash of the camera does not highlight on 4 meters.

The output one is to install the camera on the photochative and make the desired shots with a long exposure. The improvised tripod was assembled with his own hands for ten minutes from the plastic bottle of the filled nails and the fastening screw of the camcorder. Recently, on hiking conditions, a tripod for night filming was repeated.

How to make photoshota with your own hands

1. Collect the critical mass of components. Pat bottle. Standard screw with an inch thread for fastening photos and video equipment. Very suitable screw from the casing of old Soviet film cameras. The groove on the screw between the carvings and the cap will allow it to be conveniently fixed on the traffic jam. Depending on the length of the screw, if necessary, needed washers, in my case only two pieces.

2. Drills a hole in a plastic bottle cap with a diameter of 4.3 mm. I drove a 4mm drill, and then it also increased the diameter of the hole.

3. Screw the screw into the cover of the cover from the outdoor side to cut the thread. If the screw fluently passes into the hole, this is permissible, but on hiking conditions it is fraught with the loss of the main fastener.

4. Unscrew the screw. We put the washers inside the covers and screw the screw from the inside.

5. We screw the lid to the regular fastening of the camera. If you cannot attach tightly, you need to add washers.

6. We take a bottle, we fall asleep inside on 1/2 or 2/3 of sand or small pebbles, in the extreme case you can pour water than the bottle will be harder, the stable will be a tripod.

7. Close the bottle with a lid with an attached camera - a tripod is ready.

A bottle with a rubber band can be mounted for trees and other vertical subjects.

In hiking conditions, it is enough to bring with you only the cover with a screw (this is a photocuttal head;)), I think there will be no problems with searching for a suitable bottle.

How to make the camera fastening on the bike do it yourself

The site published a way of making a simple photo of a podat from a plastic bottle. But the original standing head design allows you to fix the camera on different objects with your own hands, for example, by bike, thereby make a cheap alternative to the photo cameras such as Gopro.

The sequence of actions for a bicycle retrofit is shown below.

1. We take PET bottle. It is enough to take a bottle with a capacity of 0.25 liters. And than the walls of the bottle thinner, the more dense the fastening on the steering wheel will sit.

2. Cut off with scissors or a knife of the bottom of the bottle. We work carefully to not cut down.

3. Cut the PET bottle of 5-7 sectors, and cutting up to dense plastics in the neck area.

4. For the best flexibility of the sectors received, additionally cut each sector for another two or three bands. Strips cut to the narrowing of the sector.

5. We wake on the steering wheel at the installation site of the homemade bracket of the fastening of the camera reinforced tape, and the tape is suitable. Winding is necessary to prevent possible gliding design on the steering wheel.

6. Weient the future fastening over the angle of inclination to the horizon, I will fix with a slight tilt to the ground.

7. Sequentially, first with the help of pieces of scotch, we attach the workpiece with two strips stretched along the steering wheel. Then we attach strips wrapped around the steering wheel. All strips are not secure. We fix only those strips that give tight contact with the place of fastening. In this embodiment, only five strips are screwed.

8. Cut extra stripes and protruding ends.

9. For beauty, wind the place of fastening with a scotch or tape.

10. We screw the head to the camera and install the camera on the bracket made by your own hands. Weient the shooting direction.

Having done a tripod for the camera with your own hands, you can create a unique accessory for your camera.

With it, the picture of the received rollers will be well stabilized and you do not have to spend a big amount, because the product can be created from the girlfriend.

Content:

In the process of creating pictures or beginner photographers often face the problem of the blurred frame.

Stabilization of the image depends not from the place of shooting, but from a good tripod, which will reliably hold the camera, not allowing it to move.

The optimal option for creating high-quality photos and video is the use of a tripod. Camera stands can be several types:

Tripodes are the most stable designs with three supports that are installed on the floor or table;
Monopods - standard stands with a magnetic or ordinary base;
Multipodes;
Stand belt. Used more often for video;
Rope tripods and other suspended structures.

Making a steady tripod do it yourself

Tripod is the most expensive type of tripod. On specialized sites, the price of the structure can reach up to 5-7 thousand rubles.

But is such a spent justified if the stand can be made independently?

To create your own tripod, you will need 2 rectangular tubes, the faces of which have a rounded shape. Also, you should purchase 2 skiings of sticks from aluminum material.

To create a strong base, take a piece of the chrome pipe from steel (about half a meter long). To connect all items, you must purchase a screws, screws, nuts with washers.

From repair tools you need:

Standard drill with a drill;
Canvas for hacksaw;
File;
Wrench;
Ordinary screwdriver;
Hammer, sandpaper;
Two small wooden boards (squares 10x10 centimeters);
Pliers.

Take three rectangular tubes and cut three small pieces from it, as shown in the figure below. Take out the inscriptions and beat the "ears" by creating brackets.

Three such details should be obtained:

Fig.3 - Faceted Strolling Elements (Total 3)

Take the ski shelves and spit them into several emery sheets. Make sure that the paint is removed. Now cut both elements in half.

In the future, half of the polished stick will be the base of the tripode.

Fig.4 - Grinding of parts

Take one of the wooden boards and make a round hole in it for installing the camera and its mounting.

The diameter of the hole must match the diameter of the tube polished earlier:

Fig.5 - Creating a hole

Now go to the creation of the drafts of the tripod. One of the brackets made in the first step will be used as an attachment.

Install the bracket on top of the tube, as indicated in the figure below and drill the screw hole so that it is possible to adjust the position of the tripod.

Fig.6 - Fastening one bracket

Install the chrome tube into the base hole. Then, set the three bracket to the base, to each of which the rectangular tube is attached to the screws.

The following design should be obtained:

Fig.7 - Ready base for the tripod

Now take the second board, which is identical to size from the first. Make another bracket and attach it in this way:

Fig.8 - Creating the upper part of the attachment of the tripod

Take the self-tapping screw and drill it into the bottom so that part of the part appears on its reverse part.

It will be screwed to her camera, so you carefully select the dimensions of the self-press:

Fig.9 - Completion of the foundation

As a result, the following tripode design should be obtained:

Fig.10 - finished product

As you can see, the homemade tripod externally does not differ from the purchase. Its main plus - the base can be rotated, which allows you to set the desired view of the picture.

If you take the boards of a larger size, you can create a design that will endure more intense cameras.

Having put forward part of the tripod, you can install the chamber both in the horizontal and vertical position:

Fig. 11 - Example of using self-made tripod

DIY: Cheap homemade tripod

This version of the tripod resembles a simple stand for the camera. It is possible to use it to install the camera on the table or other elevated smooth surfaces.

As practice shows, such a tripods make autofocus more accurate, because during shooting the gadget does not move at all.

To create a tripod at home, you will need several inexpensive details:

Plastic bottle of soda. We will use the standard 0.5 liter container. Notice the more the bottle volume, the better the stability of the design. The ideal option is the use of five-liter containers;
Bolt, the caliber of which is suitable for a tripod connector on your camera;
Two washers standard size;
Nut.

Fig.12 - Preparation of materials

It is advisable to take a bottle with a wide neck, so you can achieve better stability, because the lid is the base of the tripod. It will stand the camera.

The following scheme should be obtained:

Fig.13 - Creating a base for tripod

The resulting product should not be fused or unwind. You can use a tripod already in such a state if the camera is light. It will keep well.

If you need to lift the gadget over the surface, use the remaining part of the bottle.

With it, you can drag the future tripod so that it does not throw away and retained the camera well.

A simple weighting option is water. Just type it in the bottle and tighten the lid. At the resulting product, attach the camera.

Also, you can pour a full bottle of sand - this will reduce the likelihood that with a possible falling water will go and damage the camera.

The homemade stand for the camera will look like this:

Fig.14 - Exterior of homemade tripod

As you can see, the product is very practical and you will not spend a penny on it. Operating Tips:

You should not use large cameras with such a tripod. Korea, he will not keep a weighty gadget;
Install the tripod only on smooth surfaces, as it is impossible to fasten it, which can provoke the drop of the chamber;
Carefully contact the bottle, which is filled with water so as not to shed liquid to the device.

Creating a magnetic tripod

Using the idea of \u200b\u200bprevious instructions, you can create not just a steady tripod.

Attaching a durable magnet to the base, you will receive a universal mount that can be installed not any surface.

Often, such products are used in cars for shooting videos, because the magnet firmly holds the camcorder, not allowing you to create blurred pictures.

Magnet is better to buy as thick as possible. The more its dimension, the better the camera will be fixed on the surface. If necessary, the mount can be fed.

Fig. 15 - example of a magnetic tripod for the camera and its mounting to the surface

A well-made product can fasten the camera even in a vertical state.

Stable tripod from razor machines

This option is perfect for beginner photographers, which are not yet ready to spend large amounts for the purchase of professional accessories for the camera.

The stand elevates the camera for 10-15 centimeters above the surface. Suitable for location on the table, floor or other smooth coating.

Fig. 16 - example of a finished stand

To create a short tripode, you will need:

Three shaving machine;
Small board;
Super glue;
One screw whose length is 5 cm, and the diameter is 0.5 cm;
Nut;
Sealant;
Varnish of any color;
Drill.

On the board, drink a small triangle that will be the base. On his center, make a round hole. Screw the screw in the resulting hole.

Attach three machines to the sides of the triangle and paint the design with colored varnish.

Place the ring for the seal on the screw and screw the nut. Secure the camera.

Fig.17 - Example of using the stand

Rope tripod

This version of the tripod is perfect in the event that you need to take pictures on the street, but there is no possibility or the desire to carry with you the sweaty structures for fastening.

Rope tripod is an accessory that can be done on its own in less than 5 minutes.

His feature is that the stand you can put in your pocket, and if necessary, consolidate anywhere: on the tree branch, table, shop and other places.

Reliable stand allows you to improve the quality of photos in the dark and twilight. Autofocus will start working at times better, and you will get excellent pictures even with detailed viewing under the magnification.

After executing the instructions, you will receive such a tripod:

Fig.18 - Simple stand for a chamber from a rope

You will need:

2-3 meters good rope;
Bolt with a hook whose thread has a step ¼. Such a kind is suitable for most cameras, because the bolt is attached to the base of the camera into a special connector;
Camera himself. For such a simple design, too heavy gadgets should not be taken. Suitable a regular digital camera.

The required bolt can be purchased at any farm store in less than 20 rubles. The rope will cost 150-200 rubles, depending on its diameter and strength.

Those who are engaged in photography know to get a high-quality snapshot, you need to provide the clarity of the focus. Make it, fixing the camera in a fixed position, for example, on a tripod. The latter are in the market with different models, manufacturers. It is not suiced, therefore more those who are engaged in photography professionally, or not crammed in money.

But, if desired, a tripod for a camera can be made independently. At the same time, inexpensive and affordable components are used, which results in the end, to obtain a reliable device, the consumer properties of which is not worse than that of factory.

It is not necessary to invent your design. The problem has long been solved by many craftsmen - you can take advantage of their suggestions. For example, described below:

As components for the future tripod can be:

Shaving machines - they need three pieces;
Will be suitable for the period, but not lost view;
Small board;
Bolt, in which a diameter is 5 mm, and the length is 4 ... 5 cm;
Ring for sealing and nut under the bolt;
Glue, for example, "moment"; Black enamel (can be replaced by Kuzbass varnish).

Start work with the preparation of a wooden base. An equifiable triangle is cut out of the board, the length of the sides of which is more than the size of the razor blades on the half-meter. In the center, using the drill, arrange a hole with a diameter slightly less than that of the bolt's terminal.

Applying effort into the resulting hole bolt until it stops his head into the base. The wooden detail curls a little angles, surface surface; Then covered with black paint or Kuzbass varnish.

Shaving machines heads from the blades side are glued to the sidewalls of a triangular base. The free end of the bolt should be directed upward - to the side opposite to the direction of the pens of razor machines.

On the free end of the bolt screw the nut, it is easily tightened. This fixes the position of the bolt, does not allow it to move in the hole.

Tripod ready. When using it with the ends of the shaving machines, they are installed on the surface. From above, on the protruding end of the bolt the camera is fixed.

Before making an accessory for your smartphone, you need to think about how to use, because the chassis of the finished tripod should be strong.

First of all, it is necessary to deal with what tasks will perform a manufactured tripod. If it is necessary to use it constantly, then it is necessary to think about which of the materials to choose that it serves durable. If it is planned to apply not so often, but I want to save, you can take raw materials that always have at home. Let's get closer to business.

If you perform a wooden stand for a camera or a smartphone, it is better to cover it with a verse - so it will last for a long time.

From plinth for plastic windows

When the glazing is changing into a more modern, some waste remains. They in this case will use. To begin with, we will prepare the entire inventory to not be distracted from work.

Materials and tools

For work it will be necessary:

plinth from plastic windows;
hacksaw;
drill;
metal tube.

Please note that the compiled plastic will not suit, as it can crack in the process of work.

Step-by-step instruction

We take the rest of the plastic and cut a part of half a half of it greater than your smartphone.
We will prepare the fastener on which the two holes will serve and insert the screw and the ball in them.
We measure the diameter of each element for fixing. Then we will apply the prepared plastic and we note where these parts will be.
We make holes on a piece of plinth with the corresponding diameter of the fintee and the ball.
Now we screw the adapter and fasten the base of the future tripod to it.
Plastic edges process with tape, scotch tape or silicone glue so that they do not scratch the phone.
Next, we screw the long telescopic tube (you can normally), we place the smartphone in the connector, and then start shooting.

GOOD TO KNOW!

If you doubt the reliability of the retaining device, the phone can be fixed using a gum. Use thin and elastic, as for slingshot.

Adjustable Tripod from Cardboard

Someone may seem that any cardboard is not able to reliably hold the phone on time. However, if you fulfill everything according to the instructions, you can get a durable tripod for long-term shooting.

The bare aluminum wire is better not to use to design supports. It is better to choose the one that has a protective shell.

Materials and tools

For the manufacture of a cardboard tripod you will need:

any cardboard box;
scissors;
line;
ball pen;
pistol glue.

Step-by-step instruction

Immediately prepare the desktop so that in the process of work, do not waste time search for inventory. Next, proceed to the manufacture of tripod.

We cut the cardboard box into several parts (you will need three parts with a size of 10 × 6 cm).
Now take one part and draw the line on it at a distance of 20 mm from each other. Make four strips and cut off too much
Now we press the line each drawn line and bend the figure outward. Then the resulting edges glue with a gun.
Now we do the same with the second cardboard, only stuck the lines at a distance of 16 mm.
We press them again and bend them, we form a glue gun with a glitter.
Next, we insert a smaller part in size into a large.
Measure the necessary distance on which the phone should be installed during the shooting and pierce the two holes in the cardboard. Insert the retainer in them (you can do from paper).
Now on the edge of the upper fragment of our tripod we make cuts that will keep a smartphone. Their depth should be at least 1 cm.
Next, form a stand for a cardboard device. For this, the remaining part of the box is gluitive to the pistol prepared tripod.

As a result of the acting actions, you get a durable home-made tripod with a stand that can be used on the table when performing selfie or shooting video.

Tripod stand for plywood smartphone

Plywood is one of the materials of the wood species. It is used for different purposes. Today we will use such a table for manufacture. Be sure to need a scheme or drawing for these purposes.

Materials and tools

To create a wooden stand on the phone you must have at hand:

simple pencil;
phaneur;
lobzik.

Step-by-step instruction

Prepare Phaneur, cut out two parts from it with a size of 10.5 × 5 cm and 12 × 5 cm.
Two fragments are thrown away, look at the edges there are no burstages.
Make drinking at a distance of 2-2.5 cm from the side edge of the workpiece. The width of the filled piece on each detail should be no more than 5 mm.
Remember that we cut off about the middle. Next, we connect two parts with each other "Paz-in-Paz".
On the details that have a smaller length, we make the deepening of the chisel, then we are polished by sandpaper.
Now we clean our workpiece, and then cover with varnish or decorated in an interesting design.
After in the excavation, we establish our smartphone and enjoy the result.

From plywood and thin boards, you can make a lot of interesting products in the form of stands for the phone. If you create an accessory for a child, you can take the basis of the scheme of various animals or colorful geometric shapes.

Stands for tablets Desktops from wood

How to make an interesting tripod

Everyone who uses the camera on the smartphone understands that the picture quality directly depends on the fixedness of the device. The more convenient, the phone on the tripod is also reliable, the better the image will turn out.

Materials and tools

wooden bars;
holder for smartphone;
fastener element from desk lamp;
glue pistol;
thin PVC tube.

Step-by-step instruction

First of all, we will prepare all the available bars for processing. To do this, pass them from all sides to remove unevenness.
Next, take a big bar and glue small on the edges.
The wide plane will be the basis of our tripod.
Now we glue the PVC tube to the prepared bar.
Drive two symmetrical holes with a diameter corresponding to fasteners.
We insert the locking element, form a small rectangular bar with the same hole that is subsequently attached to the reacting mechanism.
From above on the resulting bar, we glue one more, slightly larger size. He will serve as a platform.
Now to the resulting design, a plastic phone holder is found in a horizontal position.

After the proceeds have done, you can use a homemade tripod as purchased. Such a device can be used at home for filming a full-length video.

Wooden stands for phone

How to make a tripod for phone from girlfriend

Among the variety of tools and materials that can be used to create homemade tripods, there are also options that are always in the house. At this stage, Pogrim is about such devices.

When there are holders for folders and papers in large quantities, they can be applied with a lot of benefit to the phone. It is from these devices that we will create a simple tripod.

For a portable stand prepare one big binder, and another smaller.
We open a big fastener, put in it the handle of the small and slam the design.
We raise the bottom holder up, then simply install your smartphone on the stand.
Ideally, it is better to ask for a mini-tripod face to avoid possible scratches on the phone body.

GOOD TO KNOW!

Such a device is convenient to carry with you in a bag, organizer or even in your pocket. Especially useful will be such a gadget for those who work in the office and always holds a cellular at hand.

BELIFT RELATING

For this purpose it is advisable to use both plastic and wooden clothespins. However, it is worth noting that the latter will better look, especially if they have been reorganized by any of the ways. We will proceed to the stand.

For the product it will take one ballpoint pen and 5 clothespins.
Confirm all clothespins from the middle to the edge with the cap.
Two extremely deposit in the opposite direction.
The following two (located from the opposite sides) raise up.
We can assume that the tripod is ready. We set the phone on it and use as a regular stand or means for shooting.

In this version of the accessory you can adjust the slope of the smartphone.

Tripod from a piece of copper wire

The next home-made version of the stand will suit more to cameras. Make this accessory is easy, the main thing is to properly prepare all the tools.

We collect the desired material: silicone tube, copper wire, brass adapters, two bolts, nippers, burner, water and cleaning for dishes, epoxy.
I burn copper wire, observing the safety rules and turn it out in water.
We carry out the cleaning of the wires pakrels, then gently place it in the silicone tube.
With the next step we wear a brass coupling on the tube, it will serve as a connecting element for a bolt and wire.
Following the bolt, we cut off the hat with a barart or saw on the metal, leaving the tail of 2-3 cm.
Next, screw in the adapter the resulting part lock it with a glue gun, and better epoxy. Outside the adapter should remain a part of 0.5 mm. This will be required to further fasten the camera.
Find the opposite side in the same way, only do not leave the bolt outside.

In the process of use, this device can be screwed onto the branches of trees and on any other support in case there is no one next to anyone, and take a picture - this is the matter of essential.

In the manufacture of accessories for electronics, it is better to take materials with a margin.

Dear users. Specify questions in the comments, tell us if you liked the ideas for creating a homemade tripod. If something is not clear, we will discuss in priority.

Perhaps it will be useful to read: