Double nautical knot diagram. Sea knot: how to knit sea knots, how to tie knitting patterns. Marine knots used for rigging

The history of the use of knots goes back many millennia. According to scientists, even cavemen used simple knots in their everyday life. The ancestors of complex types of knots are sailors. With the advent of sailing ships, the need arose for comfortable and reliable knots to secure the mast, sails and other gear. The quality of the node depended not only on the speed of the ship, but also on the life of the entire crew. Therefore, sea knots are very different from ordinary ones. Not only are they reliable, they are easy to tie and just as easy to untie, which cannot be done with conventional knots.

The classification of knots came to us from England. Usually the British divide naval knots into 3 types:

Knot - needed to increase the diameter of the rope or weave something.
Hitch - attach the rope to various objects (masts, yards, anchors).
Bend - connect ropes of different diameters into one.

There are about five hundred descriptions nautical knots, but at present only a few dozen are used, since motor ships are replacing sailing ships. The ability to knit sea knots will come in handy not only for yachtsmen, but also for tourists and fishermen. By gradually mastering the schemes below with pictures, you will quickly learn how to do this.

Although this knot is one of the most ancient, it does not differ in reliability. Its disadvantages are frequent displacements on the rope, it is not easy to untie it after heavy loads and getting wet, and also the strength of the rope decreases with such a knot. It is used for easy gripping on light rods and for splicing the two ends of the rope. More complex knots are knitted on its basis. Despite the fact that the knot is very simple, it has its own nuances. The risers should be on one side of the rope. If they are located on different sides, then such a node is considered incorrect and is called not simple, but thieves.

How to knit a straight knot:

A regular knot is tied.
From one fixed end of the end rope we make a loop.
With the free end, we enclose the hinges on the outside and put them inside.
We are tightening. It turns out the correct knot. For greater reliability, another regular knot is tied on top.

Arbor Knot (Bulin)

In yachting, this knot is used more often than others. Initially, it was used to tie the gazebo - a device with which sailors climbed onto the mast of the ship. For this he got his name. This knot has no flaws, it is easy to tie and undo. They can tie ropes of different diameters, materials and not be afraid that it will untie. It is most often used when mooring a vessel or when you need to make a loop or tie something.

How to knit an arbor knot:

We make a regular loop.
We put the free end inside the loop and weave it diagonally around the fixed end.
We skip back inside the loop.
We tighten the ends of the rope. To keep the knot strong, it is very important to tighten the ends tightly.

Figure eight knot

By appearance looks like the number 8, so the name speaks for itself. The knot is simple but very important. More complex knots are knitted on its basis. The advantage of the figure-eight knot is that it will never move or unravel under load. Also, when the rope gets wet, it can be easily tied and untied. It is used as a stopper at the end of the cable and as a fixing knot. It can be used to make handles for a wooden bucket or fasten strings to musical instruments.

How to knit a figure eight:

We make a regular loop.
We rotate our loop 360 degrees and thread the free end inside the loop.
We are tightening.

How to knit a loop eight:

Fold the free end in half to make a loop.
We make a second loop near the double end.
Rotate the second loop 360 degrees.
We pass the first loop inside the second.
We are tightening.

Noose knot

This knot is a self-tightening loop. Its advantages are simplicity and speed of knitting, reliability and easy untie. Suitable for tying to objects with a flat surface.

How to knit a stranglehold:

We make a loop at the end of the rope.
We make a second loop to make a bow.
We wrap the free end of the rope 3-4 times around.
We push the end from the back into the second loop.
We are tightening.

Your favorite trophy

You can choose up to 3 favorite trophies

Overall score

Bloody knot

In ancient times, such knots were knitted on a cat - lashes with nine or more ends. The cat was used as an instrument of torture and support of discipline on the ship - the blow was very painful, lacerated wounds did not heal for a long time. For this, the knot got its bloody name.

How to knit a bloody knot:

The free end of the rope is wrapped twice around the fixed one.
We are tightening.

Flat knot

It is used when you need to tie the ends of a rope of different diameters or from different materials. Withstands heavy loads and wetness well. But this is not the easiest knot, it is easy to tie it incorrectly. The most important nuance when knitting a flat knot is that the ends of the ropes should be parallel to each other.

How to knit a flat knot:

We make a loop from the thick end of the rope.
The thin end is wound inside the thick one.
Two turns are made over the thick end.
We are tightening.

Clove hitch

Initially, this knot was used to fasten shims - thin ropes from which ladders were made for cables. It is one of the most reliable tightening fasteners. Its peculiarity is that greater reliability is possible only under load. Also, its reliability is influenced by the surface on which it is tied. A big plus of the knotted knot is the ability to tie it with one hand. It is used to fasten the rope to objects with a smooth and even surface - logs, masts. On objects with edges, the bleed knot will not be as effective.

How to knit a bleached knot:

The free end of the rope is wrapped around the object.
An overlap is made.
We thread the end into the resulting loop.
We are tightening.

The second method (knitting with half-bayonets):

We make a loop. The long end of the rope is on top.
We put a loop on the item.
At the lower end of the rope we make a loop and put it on top of the object.
We are tightening.

Anchor knot or fishing bayonet

For more than one millennium, it has been used to attach a rope to an anchor. Also, with this knot, the ends of the cable are tied to any mounting hole. It is a reliable and easily untied knot.

How to knit an anchor knot:

We pass the end of the rope twice through the loop of the anchor or other mounting hole.
We throw the free end of the rope over the fixed end and pass it through the resulting loop.
We tighten both loops.
On top we make a regular knot for reliability.

Stop knot

It is used when it is necessary to increase the diameter of the cable.

How to knit a stopper knot:

Fold the locking rope in half.
We apply it to the main one.
With the free end of the locking rope we wrap the main and the second end of the locking rope 5-7 times.
The fixed end, which we wrapped, is returned to the loop of the retaining rope.
We tighten both ends.

Clew knot

Such a knot used to be tied up sheets - tackle for sail control. It is currently used for tying ropes of different diameters. Not suitable for knitting synthetic ropes as they are slippery.

How to knit clew knot:

We make a loop from a thick rope.
We wind a thin rope inside, bend around the loop and wind it under itself.
We are tightening.

We tie something every day, without even thinking about it - on laces, on ribbons and bows, on a tie, at home and on vacation. One way or another, nodules are present almost everywhere. Let's figure out which of the special techniques of tying a sea knot on a rope can be useful to us in extreme and hiking situations, will be the strongest and most reliable.

How to tie a knot on a rope, diagram

We all know the simple knot required to connect the two ends of one tape. But the version used by sailors is a little more complicated.

Figure 1. An example of connecting two ropes with different knots

Why is a knot on a rope good:

It connects elements of the same diameter (Figure 1);
Withstands sharp jerks well;
Does not untie on its own and does not slip;
Retains its properties even after getting wet.

But, like all connecting structures with a large number of weaves, it severely damages and weakens the rope.

How to tie a water knot

There is a clear sequence of how to tie a water sea knot correctly (Figure 2):

Arrange the running lengths for knitting parallel;
Form a closed loop with their ends, passing them under the root ends;
Make three turns of the running lines around the root ends;
Make sure that the ropes remain parallel during the tying process;
Secure the structure while tightening all ends at the same time.

Figure 2. Scheme of a water sea unit

It can be easily untied if:

Know the constituent parts, there are only two of them - running and root;
Loosen the tension - the loops will be clearly visible and the task will not be special labor.

Variety of nautical knots

There are endless types of marine weaving (Figure 3).

Among them, the most commonly used are:

Eight;
Butterfly or bee;
Gazebo;
Straight or plain bayonet;
Anchor.

Figure 3. Examples of different nautical nodes

In addition, they are all classified according to their intended purpose or the material used for them:

For tying rope and cable parts - dagger, woman, oak or water;
To strengthen the base of ropes or ropes - yufer, oyster or bloody;
Collar with free, not tightened loops - vein, perfect, burlack;
Classic tightening - figure eight and noose;
Decorative and special with original names - Turkish, cat's paw, amphora and royal, etc.

Straight

Universal weaving, known since the times of ancient Egypt (Figure 4). A straight knot consists of two semi-knots, which are sequentially tied in different directions, one above the other. At the same time, it can be strongly tightened under heavy load and strong wetness, which does not interfere with its quick untightening within a couple of seconds.

Figure 4. Straight nautical knot

Reef

One can easily say about this element that anyone who tied a bow on laces can handle it.

At sea, with its help, winches and other tackle are fastened on the open deck, tarpaulin covers are fixed on lifeboats. Below is a knot pattern (Figure 5).
Figure 5. Reef marine knot

Eight

The most common weaving (Figure 6), it is:

Flat knot

Its main purpose is to tie ropes of different thicknesses.

If there are four points of intersection, it:

Ensures the reliability of the connection and does not tighten tightly;
Distributes the load evenly, as it does not have strong bends.

All these qualities are highly dependent on the correct execution, therefore, the knitting principle does not accept any deviations (Figure 7).

Figure 7. Flat nautical knot

Simple bayonet

Easy weaving of the element allows you to hold the load in any direction and untie it underneath without much effort.

How to properly tie a knot on a rope, a diagram - you can learn from this easy way(Figure 8):

Clew knot

It is also recommended for tying strings and fasteners of different thicknesses. Material of a larger diameter is used for a regular hinge, but also on parts of the same diameter, the mount holds no worse.

The step-by-step instructions will tell you how to properly tie the clew knot on the rope (Figure 9):

Kalmyk

This type is used on sailing and Russian ships. It has long been used for naval purposes and is suitable for temporarily tying ships in the port and horse-drawn carts to a pole.

Follow the instructions to learn how to tie Kalmyk rope knots (Figure 10):

Gazebo node

Due to its simplicity and reliability, bowline is used in tourism and mountaineering, marine business. It is knitted at the edge of the rope and is a beautiful, non-tightening loop (Figure 11). A useful skill - the ability to knit it with one hand will come in handy in a number of extreme situations.

I came across Safronenko's brochure “Learning to knit knots”. It may be useful for others to familiarize themselves with this material.

For orientation in the description of the nodes used, in accordance with Fig. 1, the following terms: root end - the end of the cable, fixed motionlessly or used when knotting; opposite to the running end; running end - the loose free end of the cable, which begins to move when tying a knot; loop (open) - the running (or root) end of the cable, bent twice in such a way that it does not intersect with itself; kalishka (closed loop) - a loop made by the running or root end of the cable so that the cable intersects with itself; half-knot - a single overlap of two different ends of the same cable or two ends of different cables; wrap-around - the girth of an object with a cable (a log, a post, another cable, a ring, etc.), made in such a way that both ends of the cable do not intersect; Hose - a full turn (360 °) of the rope around an object, made so that after that the end of the rope is directed in the opposite direction; half-bayonet - carrying a rope around an object, followed by crossing its end with a cable at a right angle, without passing it into the resulting closed loop.

KNOTS FOR CABLE THICKING "Simple knot" (Fig. 1). This is the simplest knot known. To tie it, it is necessary to make a half-knot behind its root end with the running end of the cable. It can be tied at the end or at the middle of the rope. To do this, the running end of the cable is once rounded around its root part and passed into the resulting loop. Depending on how it is tied, a simple knot can be left (Fig. 2, a) or right (Fig. 2, b). ... It is not only the simplest of all the knots, but also the smallest in size. When the cable is pulled, it is tightened so much that it is sometimes very difficult to untie it. One more negative feature for vegetable cables should be taken into account - this knot, like no other, spoils the cable, since it bends it strongly and weakens its strength by about half. A simple knot is used to tie at the end of the thread so that it does not slip out of the fabric, to prevent the rope from unraveling, and also as an additional knot; for example, at the ends of sheets tied together, which serve as a rope in case of fire. A simple knot, despite its primitiveness and the property of being tightly tightened, is an integral element of many useful knots. "Eight" (Fig. 2-2). This knot is considered classic - it forms the basis of many other, more complex knots for various purposes. It can serve as an excellent stopper at the end of a thread, rope, cable. Even with a strong pull, unlike a simple knot, it does not spoil the cable, and it can always be easily untied. IN Everyday life The G8 is widely used. It is very useful for securing a rope through a hole in an object, such as the wooden handle of an outboard motor's rope starter. Two “eights” can be used to securely attach the rope to the sled. To keep your hand from slipping off the end of the dog's leash, you can use a figure eight. It also serves well for attaching strings to the tuning pegs of violins, guitars, mandolins, balalaikas and other musical instruments. "Stevedoring site" (Fig. 2-3). Like the figure eight, this knot acts as a stopper for the cables passing through the hole. It fits like the "eight", but with the only difference that the running end is inserted into the loop after it has been wrapped around the root end of the cable twice. When tightening this knot, care must be taken that the hoses at the root end do not twist and slip into the loop. A tightened stevedore knot is easier to untie by pulling on the loop near the root end. "Oyster Knot" (Fig. 2-4). Due to its symmetry, this knot is successfully used by musicians for fastening strings on the tuning pegs of a violin, mandolin and other musical instruments. In terms of its size, the tightened oyster knot is much larger than a figure-eight, and therefore it is used in cases where the holes on the pegs, for some reason, are larger than needed for a particular string. This knot has one knotting feature: it is tightened in two steps. First tie a running simple knot (see Figure 8-52 below) and tighten. After passing the running end of the cable through the loop, tighten the knot again. If the oyster knot is tightened in one go, it will not form correctly. In fig. 2, c shows a diagram of an oyster knot, indicating its symmetry. In this form, it can serve as a good de-corative ornamental knot. "Ufer knot" (Fig. 2-5). This antique sea knot can be tied in two ways. The first method (Fig. 2-5, a) is based on a simple knot and provides for inserting the running end into the loop from below between the root and running ends, followed by passing it under oneself. The second method of knitting (Fig. 2-5, b) involves tying a figure of eight and pulling both ends into its corresponding loops. The peculiarity of the knot is that it is relatively easy to untie it even if it is tightly tightened. "Multiple eight" (Fig. 2-6). If there is a need to temporarily shorten the cable or exclude an unreliable part of its length from work (in case of fear that it will break off), it is best to use the "multiple eight", which can also serve as a convenient handle for both large and small an item (cardboard box, bale, old suitcase). If you impose a "multiple eight" in the middle of the rope of a children's sled, you will get a very good handle, and it is better to fix the free ends of the rope to the sled with a simple "eight". "Multiple Eight" - a comfortable handle at the end of the dog leash. To make the knot even and tight, as you tie each full turn, tighten it with movement to the previous one. If you later need to use the entire length of the cable, the "multiple eight" is easy to untie. No matter how tightly it is tightened, it will not damage the cable. The "fire escape" (Fig. 2-7) consists of a series of simple knots, which are very quickly knitted one after another (in half a minute you can tie 20 knots). It is great for its simplicity and efficiency, but it requires a certain skill and precision in execution. Knitting of this knot begins with the formation of a certain number of closed loops (kalishki), wound up for each other. Take the running end of the cable in your left hand, stepping back from its edge 15-20 cm. Make the first peg with a diameter of no more than 10 cm so that the root end of the cable is at the bottom. Then make the same peg and press your left thumb against the tips of the others. In the same way, make 5-7 kalees, exactly laid one on top of the other. "So that they do not slide out and do not get mixed up, put them on the fingers extended upward (except for the thumb) of the left hand. You will get a kind of rope" cup "Carefully remove it from your fingers so that it does not crumble and flatten. Now the running end, which you held in your left hand, pass inside this" cup "and bring it out on the other side. on the left palm and grab it on all sides with five fingers. With the bent tips of the fingers of your right hand, hold the upper edge of the "cup" and slowly, without jerking, pull the running end of the cable sticking out of the "cup" upward. simple knots will be tied. Their number will correspond to the number of stalks made, and the distance between them will be the length of their circumference. Knots can be quickly tied by fixing one end of the rope to the battery, to the leg of the bed (chair), the other end will be thrown go out the window and, if necessary, climb down the rope. Such a “ladder” can help a person who has fallen overboard. It is convenient for several people to pull out a car stuck in the mud. To make it easier to pull, tie a "fire escape" on the ground so that the knots go every meter or so.

TIGHTENING ASSEMBLIES "Self-tightening assembly" (Figure 4-18). This primitive knot is perhaps the most original. A traction commensurate with the strength of the cable can be applied to the root part of this knot, and it will be securely held. The greater the thrust, the more the free running end is pressed by the hose, and the knot tightens itself. But it is reliable only when tied around the log and constant effort is applied to the root end. If the force is applied to the cable at the same time, in jerks, then the running end can slip out from under the root end of the cable. The self-tightening assembly can be used in cases where the suspended load is motionless and the direction of traction to the root end does not change. It is convenient for them to hang bags with food on the crossbar in warehouses in order to save them from rodents. Having released the running end of the cable, the suspended bag can be smoothly lowered. “Self-Tightening Half-Bayonet Knot” (Figure 4-19). By adding one or two half-bayonets to a self-tightening knot, we get a more reliable knot that can be used for various needs. "Chinned knot" (Figure 4-20). This knot consists of two half-pieces tied in the same direction. There are two ways to tie it. The first method is used in cases when one of the ends of the object around which the knot is knitted is open and accessible (Fig. 4-20, a), the second, when the cable has to be carried directly around the object (Fig. 4-20, b) ... With the help of a knotted knot, you can attach a rope to a smooth post or a crossbar, tie a bag, pull a rope between two poles, tie a bowstring to a bow, anchor the boat to a pile or stake dug in on the shore, attach a twine to a thick cable. It is very convenient for feeding a tool to a height (for example, a hammer). When weaving many types of fishing nets, bleached knots form the first row of knitting. However, when using a knotted knot, you should always remember that it is reliable only with constant pull on a cable or rope. Retractable Bayonet (Figure 4-21). This knot is more perfect and more reliable than the bleached knot. It can also be used in cases where the direction of the cable pull is at an acute angle to the log or cable to which it is attached. Retractable bayonet holds even when the thrust is directed almost along the br? In -. ^ A. Unlike a knotted knot, a sliding bayonet has not two, but three "covering the object of the hose; one on one side of the root end and two on the other. When tying this knot, it is necessary to take into account which direction the thrust will be end, and depending on that knot. It is easy to remember: on each side of the pull, there are two hoses. When using a sliding bayonet, do not forget that it is reliable only under load and does not like sharp weakening. "Constrictor" (Fig. 4-22). The knot, known all over the world under this name, which in translation from Latin means "boa constrictor", is one of the most tightly tightened knots. At the same time, it is considered one of the most difficult to untie knots. As a rule, it is not even untied, it only serves once. The constrictor is well tightened on round objects that do not have sharp corners; in this case it is irreplaceable. This is a very useful and important site. With its help, you can, for example, tie a bag very tightly, a soccer ball chamber valve, squeeze a leaking rubber hose, pull a carpet, a bag, a cotton blanket on top, tie a bully's hands, put a tourniquet on a wounded limb, and much more. ... "Double Constrictor" (Figure 4-23). This knot is more difficult than the previous one and tightens even more. "Python knot" (Figure 4-24). In principle, it is similar to a constrictor. It can be used, except for those cases as a constrictor, and for connecting two transverse slats (Fig. 4-24, b). Their connection with this knot will be much stronger than with nails. They can tie wooden slats of a kite, and when building a braided fence, tie one rope to another at a right angle. "Blind loop" (Figure 4-25). This knot is also called a tag knot, since it is very convenient to use it for tying keys together, for storing washers and other items with a hole, as well as for tightening the neck of the bag when tying it. "Stop Knot" (Figure 4-26). Sometimes it becomes necessary to hold the cable under tension. This is done with the help of another cable, which is attached with a stopper knot to the cable to be stopped. If the pull of the cable that needs to be stopped is to the right, then the running end of the stopping cable is placed on top of the cable with a hose to the left, then another hose is made and the running end of the stopping cable is led towards the first and second hoses, into their clamping, and then to the right around of the rope in the twine, making one or two more hoses, and in two or three places they put strong fights or fix them "under themselves". "Swing Knot" (Fig. 4-27). If you decide to make a swing in the country or in the yard of your house, then do not look for a better node. "Choke with the floor with bayonets" (Fig. 4-28). This knot, proven by many centuries of experience at sea, has long been used on the coast. It is reliable and very durable, it tightens extremely tightly around the object, but when the pull on the cable stops, it is very easy and simple to untie it. The choke with half-bayonets is widely used by lumberjacks. In many foreign languages it is called "forest knot" or "log knot". To lift a heavy log or pipe, instead of special rigging devices, you can do with a plant or steel cable of appropriate strength. But for this you need to be able to tie the knot correctly. It must always be knitted a little to the side from the middle of the log (pipe). Having withdrawn the running end of the cable from the loop constituting the knot, it is pulled towards the end of the object being lifted, from which there will be a thrust, and two half-bayonets are made. But, as a rule, two half-bayonets are made before tying the stranglehold, since the root end of the tackle is already fixed to the lifting mechanism. The slack in the cable between the choke and half-bayonets before lifting must be selected. Having lifted an object with a crane, it is better to deliver it to the place in one go, without lowering it to the ground. It should always be remembered that this knot must be checked before each lift (if it is carried out in two steps). It is also important in which direction to do half-bayonets on the log. They should be laid in the direction of the descent of the cable. Lifting heavy objects with a stranglehold without half-bayonets is considered dangerous.

NON-TIGHTENING KNOTS "Simple half-bayonet" (Fig. 3-8). It is the simplest of the non-tightening knots, is widely used - it serves as the final element of many knots. A knotted half-bayonet with a running end attached by a grapple firmly withstands strong pull. It can move towards the object, but it never drags on. "Simple bayonet" (Figure 3-9). Two identical half-bayonets make up a knot, which is called a simple bayonet. This non-tightening knot is one of the simplest and most reliable knots for fastening. For a properly tied bayonet, its running end, both after the first and after the second, should protrude equally above or below its end. In an inverted, that is, an incorrectly tied bayonet, the running end after the second kolyshki goes in the opposite direction, not like after the first one. If the half-bayonets of a simple bayonet are made in different directions, then when the cable is pulled, they will come together and the knot will tighten. More than three half-bayonets should not be thrown in such a knot, since this is quite enough and the strength of the knot as a whole will not increase with a large number of half-bayonets. This simple, but reliable knot can be used in all cases when the cable needs to be temporarily attached to some object for strong traction, for example, for a hook when towing a car. "Bed bayonet" (Fig. 3-10). This non-tightening knot holds firmly even during heavy rolling, and if necessary, it can be easily and quickly untied. "Simple bayonet with a hose" (Fig. 3-11). This knot differs from a simple bayonet in one additional hose around the object to which the cable is attached. Two hoses around the object make this unit more reliable under prolonged loads - due to the additional hose, it will not fray as quickly as a simple bayonet. "A simple bayonet with two hoses" (Figure 3-12). It differs from the previous knot with an additional, third hose, which increases the strength and reliability of the knot if the cable is under constant pressure. "Bayonet with detour" (Fig. 3-13). More symmetrical than a simple bayonet with two hoses, and in case of a change in the direction of the thrust, it moves less along the object for which it is tied. To tie a bayonet with an overhang, you first need to make one hose around the object with a running end, surround it behind the root end and again make a hose, but in the other direction. After that, one or two half-bayonets should be made. Reverse bayonet (Figure 3-14). Often a situation arises when the running end of the cable is wrapped around an object (logs, etc.) very difficult. Using a reverse bayonet, you can wrap the cable around the desired item once and still tie a knot with two hoses around the item to which the cable is attached. To do this, the running end of the cable must be folded at a length of 2 - 3m twice and, looping it around the object, pull the loops towards you. Now the running end of the cable needs to be threaded into this loop, and at the root end, take out the slack and finish the knot with two half-bayonets. "Fishing bayonet" ("anchor knot") (Fig. 3-15) Recognized by sailors of all countries as the most reliable for anchoring the rope. It can be used in all cases when working with cables, when they are subject to strong traction. "Mast bayonet" (Fig. 3-16). First, a knot is tied around the object to which the cable is attached (see; Fig. 4-20) and a simple bayonet is made at the root end of the cable - a reliable and simple knot is obtained. To prevent the mast knot from tightening, the first knot is not fully tightened. "Port node" (Fig. 3-17). First, near the bollard, you need to make several slips with the running end of the mooring cable. After that, fold the running end in half and in this form, in a loop, pass it under the stretched root part of the cable, turn the loop 360 ° and put it on top of the curbstone. This knot does not slip, holds it securely. The cable can be released at any time, even if it is under strong tension. To do this, you need to slightly select the running end passing under the root end and increase the loop, after which it will be easy to throw it off the pedestal.

KNOTS FOR CONNECTING TWO CABLES "Oak knot" (Fig. 5-29). Its positive qualities are the speed at which it can be tied, and reliability. It is used only in exceptional cases when it becomes necessary to very quickly tie two cables. When connecting vegetable cables, the connection has a significant drawback: a tightly tied knot is very difficult to untie later, especially if it is wet. In addition, a rope tied with such a knot has less strength and, during operation, creates a danger of catching on something during its movement. To connect two cables, their ends must be folded along together and, stepping back from the edges 15-20 cm, tie both ends with a simple knot as one whole. Do not try to tie synthetic ropes and fishing line with this knot: it crawls on them. The Flemish Knot (Figure 5-30). This is one of the oldest naval knots, which was used to connect two both thin and thick cables. In fact, this is the same figure eight, tied at two ends. First, make a figure 8 at the end of one of the cables to be tied (see Figure 2-2). Towards the exit of the running end from it, enter the running end of the second cable and repeat the figure eight tied on the first cable. After that, grabbing each end on the left and right, evenly begin to tighten the knot, trying to maintain its shape. Pull on the root ends of the cables for final tightening of the assembly. There is also a second way of knitting: with cables folded about one meter long, we tie a figure eight, but at the same time you will have to carry around and thread it into a loop along with the short running end of one of the cables and a long root - this is the inconvenience the second way of knitting. The Flemish knot connection of the two cables is considered to be very strong. This knot, even when tightly tightened, does not spoil the cable and is relatively easy to untie. In addition, it has excellent quality - it does not slip and holds securely on the synthetic line. "Flat knot" (Figure 5-31). This knot has long been considered one of the most reliable knots for tying cables of different thicknesses. Having eight weaves, the flat knot never tightens too much, does not creep or spoil the cable, since it does not have sharp kinks, and the load on the cables is evenly distributed over the knot. After removing the load on the cable, this knot can be easily untied. Its important advantage is that it is really flat. There are two ways to knit this knot: a loose knot with tacking its free running ends to the root ends or half-spikes at their ends (Fig; 5-31, a) And without such a tack when the knot is tightened (Fig. 5-31, b). A flat knot tied in the first way (in this form it is called "Josephine's knot") on two cables of different thicknesses almost does not change its shape even with a very high thrust and is easily untied when the load is removed. The second method of knitting is used for tying thinner cables, and the same or almost the same thickness. In this case, it is recommended to first tighten the knotted flat knot with your hands so that it does not twist with a sharp pull. After that, when a load is given to the connected cable, the knot crawls and twists for some time, but, having stopped, it holds firmly. It is untied without the application of special efforts by shifting the loops covering the root ends. Since a flat knot has eight intersections, it can be tied in different ways - there are 256 different options for tying it. But not every knot from this number, tied according to the principle of a flat knot (alternating intersection of opposite ends “under and above”), will be securely held. Ninety percent of them are unreliable, and some are even dangerous for tying cables designed for strong traction. Its principle depends on the change in the sequence of intersection of the tied cables in a flat knot, and it is enough to slightly change this order, as the knot acquires other negative qualities. In fig. 5-31 there is a knitting pattern that has been tested and tested in practice. Before using this knot for a responsible business, you must first remember exactly its scheme and tie the cables exactly along it without any even the most insignificant changes. Only in this case, the flat knot will serve you faithfully and will not let you down, "Hunting knot" (Fig. 5-32). This new knot was invented by the English retired doctor Edward Hunter (translated from English - "hunter"), and the receipt by the author in 1979 of a patent for the invention caused a sensation in the maritime circles of many countries. In essence, the hunting knot is a successful intertwining of two simple knots tied at the ends of the cables. He perfectly holds on all cables, including the thinnest synthetic lines. "Bramskot knot" (Fig. 5-33). This knot is also reliable for tying two ropes of different thicknesses, both plant and synthetic. Its reliability also lies in the fact that it does not immediately untie when the pull on the cable stops. Furrier's knot (Fig. 5-34). This wonderful knot is relatively simple, compact, has enough intersections to provide strong tightening, and can be untied without much difficulty. It can be successfully used for tying synthetic ropes and fishing lines. There are two ways to knit it. "Surgical node" (Fig. 5-35). This site is still used by physicians in our time. First, two semi-knots are made one after the other with two ends, which are then pulled in different directions. Then they tie another half-knot on top, but in the other direction. The principle of the knot is that the first two half-knots do not allow the two ends to be pulled apart in different directions, while another half-knot is knitted from above. This knot is convenient to use when there is a need to pull off and tie some elastic bale or carry with a rope and tighten the first half of the knot on the rope, which, without letting go of its ends, has to be pressed with a knee. "Academic Hub" (Fig. 5-36). This node is similar to a surgical one, differing only in that instead of one second semi-node, it has two of them. It differs from its progenitor - a straight knot (see Fig. 6-39) in that the running end of the cable is wrapped around the running end of another cable twice, after which the running ends lead towards each other and again carry them around twice, that is, below two semi-knots and two semi-knots on top, but tied in the opposite direction. This gives it the advantage that when the cable is heavily loaded, it is not as tightly tightened as a straight knot and is easier to untie. "Dagger knot" (Fig. 5-37). This knot is considered one of the best knots for tying two large diameter plant ropes. It is not very complex in its design and is very compact. It is most convenient to tie it if you first put the running end of the cable in the form of the number "8" on top of the main one. After that, thread the extended running end of the second cable into the loops, pass it under the middle intersection of the figure eight and bring it over the second intersection of the first cable. Next, the running end of the second cable must be passed under the root end of the first cable and inserted into the loop of the figure eight. When the knot is tightened, the two running ends of both cables stick out in opposite directions. The knot is easy to untie if you loosen one of the extreme loops. "Weaving knot" (Fig. 5-38). This knot embodies simplicity, reliability and compactness with instant yarn tying. "Straight Knot" (Figure 6-39). Apparently, only in our country there is an unreasonably respectful attitude towards this site. Sailors of other countries treat him more soberly and even with prejudice. After all, it cannot be used to connect two cables, which will be subject to strong traction: it crawls and is dangerous when it gets wet. This knot claimed more lives than a dozen other knots combined. Unfortunately, many compilers of various manuals and manuals for riggers, builders, firefighters, climbers and mine rescuers still recommend a straight knot for tying two ropes. But it can be sufficiently reliable only if its running ends are attached to the root ones. This knot is good for packing things, bundles, etc. A straight knot consists of two semi-knots tied one after the other in different directions. This is the usual, easiest way to knit it (Fig. 6-39, a). Sailors who use this knot since ancient times to tie ropes, use a different method of knitting (Fig. 6-39, b). Weavers who use a straight knot to tie broken threads of yarn tie it in their own way, in a special, convenient way (Fig. 6-39, c). This knot, which, according to the unanimously accepted characteristic of our specialists, “is tightened so that it cannot be untied and will have to be cut,” it turns out, even wet and tightly tightened, can be untied very simply, in 1-2 seconds. Take the root end A in your left hand (Fig. 6-39, d) and, so that it does not slip out of the hand, make a couple of slips around the palm. Also, take the running end B in your right hand. Pull the ends sharply and strongly in different directions. Without releasing end A from your left hand, clench the rest of the knot with your right fist, holding it with your thumb and forefinger. Pull the root end A to the left and the knot will untie. The whole secret lies in the fact that when the ends A and B are jerked in different directions, the straight knot turns into two half-bayonets and completely loses its properties. It is also easy to untie if you take the root end of the D in your right hand and pull the leading end B firmly to the left. Only in this case, the end of G then needs to be pulled to the right, and the rest of the knot (half-bayonet) - to the left. Unleashing a straight knot in this way, remember that if you pulled the running end to the right, then pull the root to the left, and vice versa. When untiing a straight knot, one should not forget that with what force it was tightened, it is also necessary to pull with the same force at one of its running ends. Even a wet straight knot tied on the thickest plant cable, which is under strong traction, can always be untied by taking one of the running ends to a spire or winch. In any case, there is no need to cut the cable. There are three dangerous knots, very similar to a straight knot: "woman" (Fig. 6-40), "mother-in-law" (Fig. 6-41) and thieves (Fig. 6-42). The primitive "woman's" knot, unfortunately, has firmly taken root in our everyday life, and most people, having mastered this knot in childhood, so strongly believed in its utility that they do not want to hear about any other knots. However, this traitorous knot in the entire history of mankind has done many troubles and even took many human lives. A "woman's" knot consists of two semi-knots tied sequentially one above the other in the same direction. If they tie two ropes and pull, then you can immediately see that the knot begins to move along the rope, slide along it. And if you tie it close to one of the ends of the rope to be tied, then when pulling, it can slip off. But, oddly enough, the woman's knot is used in their work by sailors and fishermen of some countries. In addition to its negative qualities (sliding and not giving in to untie), they caught one of its positive qualities: under certain conditions, it instantly turns into a simple bayonet (see Fig. 3-9) - into one of the simplest and most reliable ¬nh naval knots for securing the mooring of the vessel on the shore behind a bollard, bollard or mooring bollard, without leaving the vessel ashore. And this is done with the help of the "woman's" knot despised by the sailors. To do this, a loop is made at the end of the cable, which they intend to bring to the shore for fastening it with a simple bayonet around the pedestal, while the running end is connected to the root end by a "woman's" knot, which is not fully tightened. From the side of the vessel, this loop is thrown onto the bollard and by a jerk for the root part of the mooring, the "woman's" knot turns into a simple bayonet. Some people, tying two ropes together, somehow manage to tie the so-called "mother-in-law" knot (Fig. 6-41), somewhat reminiscent of a "woman's" (Fig. 6-40). If the last running ends come out of the knot on one side, then at the "mother-in-law" knot they come out from different sides diagonally. The "mother-in-law" knot is as tricky as the "woman's" (if not more). It should never be used under any circumstances. "Thieves' knot" (Fig. 6-42). At first glance, it hardly differs from the straight knot (see Fig. 6-39) and it seems that it is akin to it. But if you look closely, it becomes clear that the running ends of the thief's knot come out of it diagonally. The thief's knot, like the "woman's" and "mother-in-law" knots, are shown for clarity, to emphasize their similarity and difference with the straight knot. The use of these four knots is not recommended as they are not reliable for tying two cables together.

NON-TIGHTENING HINGES "Oak loop" (fig. "7-43). This is the simplest loop of all existing non-tightening loops. It is knitted with a simple knot at the end of a cable folded in half (hereinafter, a circle indicates a working loop). and safe; unlike the oak knot, it can be applied on a synthetic rope. However, oak; the loop weakens the rope, bending it; it is very "tight", and it is very difficult to untie it. "Vein loop" (Fig. 7-44). If, tying an oak loop with a double-folded running end, make an additional hose, then you get a loop that will be a little easier to untie. It is used for thin fishing lines. The Flemish Loop (Fig. 7-45). Tied with a figure eight on a double-folded cable, it is a strong and easily untied loop at the end of the cable. The Flemish loop is suitable for knitting both thick and thin ropes. It almost does not weaken the strength of the cable. It is used for fixing strings of musical instruments and other purposes. The Perfect Loop (Figure 7-46). The knot used to knit this fixed loop at the end of the cable is simple, reliable and does not slip even on the thinnest synthetic line. The perfect loop is very popular with anglers abroad. "Gazebo knot" (Fig. 7-47). The second name for this knot is the bowline knot, or bowline. This is one of the oldest and most amazing knots ever invented by man. He is often referred to as the "king of knots"; not every sea knot can compare with it in the number of positive properties that it possesses. It is surprisingly easy to knit, even with a strong pull it never tightens "tightly", does not spoil the cable, never slips along the cable, does not untie itself and is easily untied when needed. In appearance, it looks like a weaving knot, but its running end does not go into the loop of the other end, but into the loop of its root end. The arbor knot, despite its amazing compactness, contains at the same time the elements of a simple knot, half-bayonet, weaving and straight knot. Elements of all these nodes in a certain combination give the arbor node the right to be called universal. The main purpose of the arbor assembly is to tie a person with a rope under the armpits when lifting to a height or when lowering. A gazebo can be inserted into the non-stretching loop of this unit (a small wooden platform-board used to lift a person onto the mast or lower it overboard during painting or other work). This knot can be successfully used to tie two cables of the same or different diameters or cables made of different materials (the connection with the help of two arbor knots with loops of two cables made of different materials will be the most reliable). In addition, a reliable tightening loop can be made from the gazebo assembly (see below "Running bowline"). The arbor knot can also be safely used for temporary shortening of the cable or in the case when it is required to exclude a worn piece of cable from work by tying the knot so that this piece falls on the loop. There are many ways to knit a gazebo knot. In fig. 7-47 shows the most rational and simplest way. In life, the ability to quickly tie a saddle knot around your waist can always come in handy. You need to be able to do this with one hand with one continuous movement of the brush, in the dark, in 2-3 seconds. It is not at all difficult to learn this, it is enough to do it several times in a row. To untie the bow knot, it is enough to slightly move the loop of the running end along the weakened root part of the cable. Double arbor unit (Fig. 7-48). This knot, which has two non-stretching loops, is used instead of a gazebo for lifting a person to a height, for raising or lowering a person who has lost consciousness, and in other cases. When knitting a knot, one of the loops is made almost half the size of the other. A man sits in one loop, the second loop grabs his torso and armpits. This allows him, having risen to a height, to work with two hands. There are several ways to tie a double bowling knot. Let's consider the simplest one. The knot is knitted with a double-folded cable. After inserting the running end (in the form of a loop) into the small loop of the knot, you need to pull it out a little and, after wrapping it around the large loop, place it in the upper part of the knot. Holding the root of the cable, pull down the right side of the large double loop with the other hand. The knot will then tighten and be ready for use. The top node (Fig. 7-49) can be used to attach temporary braces when installing masts, driving piles, planting trees. If you have a jug, the neck of which has a more or less large protrusion, you can use the top knot to make a comfortable handle for it. For carrying watermelons and large melons, it is best to use this node, because it was once used on warships to carry kernels. From a piece of any rope 2 meters long, you get a reliable basket for the largest watermelon. In this case, the knot should not be fully tightened, and its three loops must be tied with two free ends. Of the known methods of knitting a top knot, the one shown in the diagram is considered the best. Boatswain, or "Spanish gazebo" node (Fig. 7-50). It, like a double arbor, serves to raise a person up or to lower him from a height. A leg is inserted into each of the two loops of the boatswain's knot and the rope is held by hand. With this knot, you can raise (or lower from a height) an unconscious person. So that he does not fall out of two loops, one or two half-bayonets are additionally tied with the running end of the cable on his chest. Burlatskaya loop (Fig. 7-51). It is also called a harness loop, or a cannon knot. This loop can be made both at the end of the cable and at any part of it. The loop is designed to apply traction in any direction. It is easy to tie and holds securely, but before a load is applied to the loop, it should be tightly tightened by hand, since with a sharp pull it tends to turn over and slide along the cable for some time. Several loops tied in this way will help to pull out a car stuck in the mud, allow you to climb to a height or descend from a steep cliff.

TIGHTENING HINGES Running simple knot (fig. 8-52). This is the simplest knot, forming a tightening loop. When pulling on the root end, the loop is tightened, but it can be increased in size by pulling the running end away from the loop. The knot can be tied anywhere on the rope. It can be used to tighten a bag, tie a bale, attach a cable to something, anchor the boat behind a pile. A sliding figure eight (Figure 8-53). Based on the figure-of-eight principle, this knot belongs to the category of reliable, highly tightening loops. It has the property of smoothly and evenly tightening when pulling at the root end. ".-." ...: ..; ... Silk node (Fig. 8-54). This knot is borrowed from birders' unsophisticated technique. A snare made of horse hair, hair or the thinnest fishing line, with the help of such a knot, work flawlessly. The force knot is considered one of the smoothest and most easily tightened knots. Running bowline (fig. 8-55). This is the same arbor knot with a small loop through which the root end is passed. It is based on the lasso principle. The running bowline works flawlessly. It is used to catch floating logs and snags, they search for and raise the anchors left at the bottom. Tightening noose (fig. 8-56). This knot is also called "scaffold", or "hanging" knot. He also finds another application: it is used when temporarily attaching a cable to objects floating in the water or when throwing and attaching a cable to any object. This knot has an advantage even over such a Good knot as a noose with half-bayonets, in that the running end of the cable cannot slip out of the loop, and therefore the tightening noose is considered more reliable. To tie this knot, the cable is laid in the form of two loops of the same size. Both loops are encircled several times with the running end of the cable, after which this end is passed into the loop facing the root of the cable, and, PULLING OUT, the extreme loop is clamped in it, The tightening noose can always be easily untied by pulling the root part cable. This grim knot can also be used to store the rope in a compact coil or as a weight at the drop end to feed it. If it seems insufficient to you as a load at the throwing end, then dip it into the water before use. The "drunken" knot (Figure 8-57) has two tightening loops. When the running and root ends are pulled simultaneously, the loops are tightened. The knot got its name, apparently, because it was used to pacify people who walked too far, putting loops on the wrists behind the back and tying the ends on the chest.

QUICK KNOTS Decoupling figure eight (Figure 9-58). If an ordinary figure eight (see Fig. 2-2) is made with a loop, that is, in its last loop, pass the double-folded running end, then we get a quick-release stopper. A decoupling running simple knot (Figure 9-59). A running simple knot (see Fig. 8-52) can be easily turned into a quick-disconnect one without changing its function, that is, using it as a tightening loop, and not as a quick-disconnect knot. To do this, you need to enter the running end folded in half into its loop. In this case, it will have two properties at once: it will tighten and quickly untie if you pull on the running end sticking out of the loop. This is a very common knot. All over the world, it is to them that horses are tied by the bridle to the leash. To prevent the knot from accidentally untied, the end of the bridle is pushed into the loop (Fig. 9-59, b). With the help of a simple untied knot, it is possible to anchor the boat to the coastal pile or pedestal in such a way that, if necessary, the cable could be given away without leaving the boat by pulling the running end, which was left long enough. The Kalmyk knot (Fig. 9-60) is one of the most practical and reliable knots. The origin of the node is clear from the name. And, although the Kalmyk steppes do not evoke associations with the sea and ships, it has long been used in the navy. Foreign sailors do not know him, he is not mentioned in foreign manuals. This beautiful knot is knitted almost instantly in the following way. Put the running end of the cable behind the object and take it, stepping back slightly from the end, from above with your left hand with your thumb towards you. Right hand Place the root end over the left fist, which is already clamped on the running end, and rotate the root end of the cable a full turn around it. Then, with the movement of the left hand, move the root end under the root of the large loop while simultaneously sweeping the running end around the same part of the cable and with the subsequent interception of the running end with the fingers of the left hand. After that, carefully drag the running end in the form of a loop through the root end hose located on the left hand (by dropping the hose), so that the running end does not straighten, and tighten the knot with the root end. The Kalmyk knot holds securely and is quickly untied if pulled by the running end. It is used for temporary attachment of the throwing end to the mooring line (ring) when the latter is fed from the ship to the berth. It is used to attach the reins to the bridle, as well as to tie the horse in the stable. If the running end, not folded in half, is passed into the loop of the Kalmyk knot, then the knot will not be a quick-release knot. In this form it is. called the Cossack knot. The untie weaving knot (Fig. 9-61) holds securely, but can be untied at any moment, even under tension. Reef knot (Figure 9-62). This one was popular in the past. the knot is commonly known as the "one bow knot". He is familiar to everyone, many tie their shoelaces on their shoes. This simple and useful knot is very similar to the straight knot and is knitted in the manner shown in fig. 6-39, except that when knitting the second half-knot, its running end is threaded into the loop folded in half. When pulling at the running end, the knot is instantly untied. Double reef, or head knot (Fig. 9-63). Sailors almost never use it: a reef knot is enough for a temporary ligament. In the dictionary of Vladimir Dahl, it is called "loop knot" and "repeyk (bow)". It is often called a byte node as well. It is knitted from the same way as a straight knot, but in the second semi-knot the running ends of the cable are tied folded in half. It is an indispensable knot for tying shoe laces, ropes, bows around the neck and bows in the hair, as well as on bundles and boxes. The mill knot (Fig. 9-64) is considered one of the most common among the many ingenious knots for tying bags. In principle, this is the same figure eight, into the second loop of which the double-folded running end is passed through. It is very convenient in that it can be tightened tightly and quickly untied by pulling the running end. Bucket knot (Figure 9-65). With this "remote-knot" knot, you can lower an object, such as a bucket of water or mortar, from a height, place it on the ground, and then lift the rope up again. This original knot can be successfully used by firefighters, builders and climbers. Imagine that a climber needs to descend from a height down the rope. He walks alone and has one rope that he still needs. The rope must be secured with a bucket knot, go down its root end and jerk for the long running end to untie the knot tied at the top.

SPECIAL MARINE KNOTS Gach knot (Fig. 10-66). When the necessary stopper is not at hand, the load is lifted with a crane or boom on a hook using an ordinary steel or vegetable cable. In this case, a slack knot is used. When the root end is loaded, the running end of the cable is pressed against the inner side of the hook neck, and the loop tightened around its back holds both ends - this is the great wisdom of this simple knot. Putting the cable on the hook, you need to make sure that the root end of the cable must pass under the running gear. However, it should be borne in mind that it is possible to lay and safely lift the load with a single slack knot only if the cable is thick enough in relation to the hook. So that the slack knot does not get poisoned when the load stops, the running end is grabbed with a temporary fight to the root end. Using the hook knot principle, it is possible to lift the bag on the hook without a rope, if its neck can be wrapped once around the back of the hook. Sliding knot with hose (Fig. 10-67). A thin rope, laid with a single hook knot, can slide off the back of the hook. If the rope is thin in relation to the hook, it is laid with a slack knot with a hose, which greatly increases the reliability of lifting the load. "Cat's paw" (Fig. 10-68). The name of this knot is justified - it looks like a cat's paw. This knot is used in cases where the sling needs to be attached to the hook in such a way that there is no excess slack. To tie this knot, the loop of the sling is placed on top of its two ends - two small loops are obtained, each of which is simultaneously twisted outward several times, depending on how much the sling needs to be reduced. Then the loops are brought together and put on the hook. The "cat's paw" is not clamped tightly, and the knot can be easily removed from the hook if there is no load on the sling. The barrel assembly (Fig. 10-69) is used when there is no special sling or device for lifting full open barrels in an upright position. On the middle part of the cable, a half-knot is knitted, the half-loops of the knot are spread apart and cover the middle part of the barrel with them. The lower part of the loop runs along the center of the bottom of the barrel, the free ends of the cable are tied with a straight knot, and if the cable is already fixed at one end, then with a bowling knot. Barrel assembly is used for loading different types containers having a cylindrical shape. In everyday life, they can quickly tie a can or a tank without a handle. Amphora knot (Fig. 10-70). The ancient Greeks invented this knot, it allowed them to conveniently carry amphorae (universal vessels with pointed bottoms, in which olive oil, olives, wine, grain, flour, etc. were stored and transported) without the risk of losing their valuable contents. This knot is not simple, it is difficult to knit, in several stages, but with its help you can make an excellent rope handle for carrying a bottle, a jug and, in general, any vessel with a small protrusion on the neck. Olympic knot (Fig. 10-71). It was named Olympic because it is made from five rings. This ancient nautical knot of the times of the "golden age of sail" on English language sounds very sentimental: "Two hearts beating as one." The purpose of the knot is to shorten the cable for a while. The Olympic knot is reliable and, despite the seeming bulkiness at first glance, it is knitted quite simply. Crab loop, or lingering fire (Fig. 10-72). The peculiarity of this knot is that it can work in two qualities: a tightening loop or a non-tightening loop. If the ends of the crab knot at the points marked with the letters A and B are pulled sharply and strongly in different directions indicated by the arrows, the knot ceases to be tightening. Taking the shape shown in the third position from the right in the figure, the knot is no longer tightened, its loop becomes constant.

FISHING GEAR KNOTS Blind knot (fig. 11-73). If a loose loop is made at the end of the leash, the easiest and most reliable way to attach a fishhook to it is to pass its end into the hook's eyelet and throw it over the hook, forming a blind loop. This method is good for both cotton and thin synthetic lines, it can also be used if the loop is made of soft wire. This knot is convenient for tying sinkers to the fishing line. Fishing eight (fig. 11-74). This is a reliable way of attaching fishing line to an eye hook. It gives full assurance that the hook will not come loose. Tuna knot (Fig. 11-75). It differs from other knots in that the eye of the hook is wrapped in two loops at the same time (like in a blind loop). Although difficult to knit, it is considered the best of all synthetic fishing knots. Stepped assembly (Fig. 11-76). This knot is most reliable for attaching a line to a hook without an eyelet. It is somewhat reminiscent of a tightening stranglehold. Leader based on the running knot (Fig. 11-77). The ability to quickly and reliably tie leashes to the line is an important matter for every angler. To tie a cross leash to the line in this way, tie a simple running knot in the right place on the line, but do not tighten it all the way. At the end of the leash, tie a figure eight and pass its end into the loop of the running knot. After tightening the last knot as shown in fig. 11-77, you will securely attach the leash to the line. Leader based on a snake knot (Fig. 11-78). This is a more complicated, but also more reliable way of tying a cross leash to a fishing line. Before tightening the snake knot made on the fishing line, insert the end of the leash with a tied figure eight into its middle. When tying the snake knot, both parts of it will come together and securely clamp the leash in front of the figure eight. Roller assembly (fig. 11 -79). To tie this knot on the fishing line, you first need to make a simple knot and insert the running end of the leash into it. The latter needs to be fixed like a multiple figure eight around the fishing line and the root end of the leash. Such a mount is quite reliable and simple.

DECORATIVE KNOTS In addition to the already considered decorative knots (oyster, straight, Flemish, flat and corrugated), in the applied arts, you can use many other beautiful knots... After all, strict, symmetrical, and often ornate and very complex in their form, knot patterns have long been used to create heraldic signs, coats of arms, emblems, brand signs, seals and vignettes. Tailors often took knot patterns for galloons and trimming ceremonial uniforms and ladies' ball gowns. Many patterns of knotted but loose knots are used by lace makers and embroiderers for finishing their products, as well as for weaving macrame. Consider the knots, which, in addition to their practical purpose, can be used in everyday life as decorative knots in various works with cables. Royal knot (Fig. 12-80). In principle, it is a reliable stopper knot, like a figure eight, stevedoring, yuffers, etc. Tied on a thick cord, the royal knot is decorative and can be used to tie the ends of cords for curtains, curtains, curtains, etc. . 12-81). Correctly tied and evenly tightened cord knot looks very impressive on cords for curtains, curtains and curtains. It can be applied at the end of a cord to switch an electrical switch. Turkish knot (Fig. 12-82). To properly tie this knot, you need to be patient. The knot is rather complicated, but it looks beautiful on a thick cable, especially if it is double tied. Can be applied to the cords already mentioned. Three-loop knot (fig. 12-83). The symmetrical design of this knot-stopper used in the maritime business has long attracted the attention of artists and graphic artists of applied art. This is a good ornament for all kinds of decorative artwork. Four-loop knot (Figure 12-84). The symmetry and a certain ornateness of this knot make it possible to refer it to the category of decorative knots. It serves artists in the selection of ornamentation for decorative finishes.

Every day, each of us is faced with such a concept as a knot. The process of tying a man's tie or a woman's scarf, sports laces is associated with this word. At home, in nature, in the country, as well as during hunting and fishing this concept simply irreplaceable.

There are many types and forms of how to tie a knot, for example, in nature, connecting logs or when strengthening a tent. All types of nodes have their own names and their practical purpose.

The technique of knitting special knots, which received the name - sea knots, acquired importance in the formation of the navy. In those days, the navy needed strong for work, as well as not difficult to manufacture units, where bulky and unnecessary parts and elements were completely excluded.

Description

A distinctive feature of nautical knots is knitting and rope pulling techniques, as a result of which the rope tension increases, which gives reliability to the knot fastening.

At rest, or rather with a weakened position of the cable, the clamp of the hinges of the marine knot is released. With this approach, the knot can be easily untied.

We can safely say that the most ingenious and durable knots were invented by sailors. They often resorted to using ropes, so at the time of their heyday sailing fleet one could count about 500 types of knots.

Each knot name was derived from the name of the gear where they were used. This is clearly seen in examples - boat, barrel, Turkish knot, as well as a number of other options.

Each knot includes several components, namely the root and running ends, if they are present, a knot, a loop (open or closed), an overhang or a hose is knitted.

Overshoot is a turnover of a specific object with the exception of crossing the ends. The hose is characterized as a full girth of the object, including crossing of opposite ends.

Scope and types

Marine knots are widely used in various fields of activity. They are indispensable for tying boats and light anchors, for lifting cargo, for fastening cables, for harnesses and gazebos, as well as for lowering various objects from a height, for fastening several poles when building a hut or wigwam.

The specified method of fastening is in demand during travel, when carrying out construction activities, fishing, hiking and in the navy.

As practice shows, the following types of sea knots are often used for fishing:

"Flemish loop"

With the help of it, the wobbler is attached to the ring on the front of the scapula and the leash of the board.

"Blind, double loop"

This type of knot is intended for fixing the wobbler on a mono line.

"Mother-in-law"

The knot helps secure the carabiners and swivel.

"Fishing loop"

Formed for a leash when needed to be connected to the main line. Common name "loop to loop"

To secure the hooks, the following types of knitting are used:

Palomar

Its strength is 92%. Suitable for hooks with rings.

"Slip loop"

Durability over 90%. Suitable for spatula hooks.

"Brand"

Durability over 90%.

Marine knots used as a line connector:

"Eight"

It is a loop with the help of which the tethering takes place and the wobbler is attached.

"Double fishing"

It is used as a connection of lines of different diameters.

Marine knots used for rigging:

"Double blind loop"

Marine knots (locking):

"Stop"

The assembly is designed for a sliding float.

Rope knots:

"Bowline"

Designed to tie a non-tightening noose. The main application is anchor rope.

"Mooring"

Applied when the vessel stops at the berth.

Variety of nautical knots

Straight

Used for fastening and connecting cables of equal diameter. When sufficiently strong loads are applied to the connected cables, given view knot is able to tighten tightly. To prevent such contraction, a wooden plank is used.

Reef

It is necessary when attaching the lining of ship covers., as well as when connecting the running ends of the cables.

Eight

Used on the ends of tackle to prevent them from falling out of blocks.

Flat knot

Used when connecting cables different diameters.

Simple bayonet

The knot is required to secure the mooring lines to the berths.

Used in situations where it is necessary to tie the cables where one of them contains a thimble.

Kalmyk

This type of fastening is widely used when you need to feed the necessary tools., buckets and various items on the mast, overboard, at the time of the necessary work.

This method is used to secure the safety cable clasping the belt of a person who is performing work on the mast or overboard.

How to increase your fish catch?

For 7 years of active fishing enthusiasm, I have found dozens of ways to improve the bite. Here are the most effective ones:

Bite activator... This pheromone supplement attracts fish most strongly in cold and warm water. Discussion of the "Hungry Fish" bite activator.
Enhancement the sensitivity of the tackle. Read the appropriate manuals for your specific tackle type.
Baits based on pheromones.

How to knit correctly?

To properly tie a specific knot, you must first study the main types of common sea knots.
Become familiar with basic concepts such as running end and root end.
Study the scheme for tying a specific knot.
Constant training. Inexperienced people who rarely tie knots often forget the technique of its implementation, so only in practice can you learn how to form a knot.
Knitting is individual because the same knot can be tied in a variety of ways.

To make a knot correctly, you need to know it and be able to knit it quickly - two main rules. It does not matter in what way a particular node was formed, the most important thing is the result.

Consider the step-by-step knitting of a stopper knot used when fishing with a sliding float:

We choose a thread, the length of which should be at least 25 cm. For fishing, it is not recommended to use a fishing line, an ordinary thick thread is best suited.
Fold the thread in half and place it next to the fishing line. The distance should not be equal. It is imperative that the length of one side should not exceed 5 cm.
Then we wrap the longest end of the thread around the fishing line and the small end.
We make up to 5 turns, and then thread the long end into the resulting loop.
.Smoothly, without a sharp stop, tighten the thread and get a knot. It is recommended to wet the knot before finally tightening the knot. Then tighten well. Advice: when creating such a node, you cannot use fishing line. This will damage the second line.
Once you have finished tightening the knot, remove the excess thread, leaving a few cm of excess on each side.

Marine knots are of great practical importance. With their help, it is possible to perform a variety of actions aimed at strengthening structures, it becomes possible to connect and connect several elements, to ensure and guarantee reliability and safety when carrying out various kinds of work.

One of the classic types of knots. On its basis, more than two dozen other more advanced nodes have been built. Each of them corresponds to a specialization for its application. The classic knot in its type is a blocking knot that is knitted on one rope. Such a knot withstands the strongest traction without damaging the rope and rope. "Eight" is considered to be the most common and one of the most reliable attachment points. This particular knot is the easiest knot to knit on one rope.

Applying the figure-of-eight knot

The "eight" knot is used in almost all areas human activity, from heavy industry and ship management to living conditions. Such a knot is used both on a rope, fishing line, elastic and metal cable, and on a rope. The principle of its use is the thickening from the nodule. Thus, it can perform both fastening functions and blockers. The G8 has become widespread in mountaineering as well. With the help of such a knot, climbers make flights on a rope to fix the carabiner. It is also used to tie strings in stringed musical instruments. It is quite actively used on fishing tackle. Such a knot is unique in its simplicity and practicality. With all this, it is very reliable, since it cannot untie when pulled. It is used in both tension and sagging ropes, ropes, cables.

Tying the figure of eight

To begin with, take one rope (type, diameter does not matter) with one running end;
We make a loop, then move the running end into the loop hole;
We tighten the knot and fix it. If necessary, you can make several knots on one rope by repeating the steps.
The figure-eight knot is ready! No wonder, it is considered the lightest of all knots.

Video

Video on how the figure eight knot is tied:

It might be helpful to read: