How to connect a rear view camera. How to connect a camera to a Chinese radio. How to connect a mirror with a rear view camera

Isn't a camera a great way to make parking in tight spaces easier? Installing a rear view camera with your own hands will not take you much time. Let's consider the installation of a mirror with a built-in camera, as well as diagrams for connecting a remote device to a multimedia system monitor.

Installation options

There are several ways to retrofit a car with a rear view camera ():

  • a separate camera that connects to a standard multimedia system or a self-installed screen;
  • a camera kit with a rear-view mirror, on which an image will be displayed when moving backwards. This can be either a separate mirror or an overhead panel that will be mounted on top of the standard reflector.

Installation

You have to decide where exactly the camera will be mounted. Installation methods:

Optional equipment

One of the main problems is the lens getting covered in dirt and ice. Even few standard systems are equipped with such a useful function as camera washing. If you install the accessory in the trunk lid of a car that has a rear window washer, then cleaning is very simple. You just need a tee, which will be implanted into the standard washer line in front of the rear window nozzle. As a sprayer, you can take a compact nozzle from any suitable car. Since the lens glass is small, there is no point in using a fan nozzle.

The second useful feature is the camera illumination, which in some models is built into the body. It is worth recognizing that in most cases the harm from this function is much greater than the benefits. The backlight illuminates the camera lens, and as a result, the image quality does not improve at night. A backlight problem may arise if the rear view camera is installed next to the license plate light. In this case, replacing incandescent lamps with LEDs can help. If this move does not solve the problem, you will have to make a protective screen.

Electronic component

Be careful when routing wires. The joints must be properly insulated. To prevent the wires from dangling or fraying, wrap them with rag tape, if possible, secure them with zip ties to the standard wiring harnesses, or secure them using the technical holes of the body elements. In the cabin, the wires can be pulled both below along the thresholds and behind the ceiling trim.

Installing a rear view camera with your own hands will not cause difficulties even for a novice car enthusiast, but you need to approach the connection much more thoroughly. It makes no sense to consider the rear view cameras that come with a special mirror. You just need to connect everything according to the instructions that are included with the device.

For normal operation of the system the following is used:

  • two-wire wire for powering the camera;
  • two-wire video communication cable. To transmit video to the monitor, wires with RCA connectors (the well-known “tulips”) are used. The cores are not shielded, therefore, if necessary, they can be lengthened or cut for pulling in hard-to-reach places. In some versions, for correct operation of the system, an additional excitation wire will come out of the RCA connector.

The excitation wire activates the radio screen with a “positive” current, causing the system to automatically switch to the mode of broadcasting images from the camera. The excitation wire is not required for all multimedia systems; in some devices, automatic switching to the rear view camera is carried out via a video link. If such a function is not provided by the radio or the device is not connected correctly, then you will have to manually change the image on the screen by pressing a special button.

Connection methods

You can connect the rear view camera and the monitor in the cabin wirelessly. This will require a special module. The module's power is connected to the reversing lamp, and from the module it goes to the camera. The second wireless module is connected to the monitor's power supply. The disadvantage of this method is interference, which often interferes with normal image transmission. Also, this method is not suitable for radios that require an excitation wire.

Let's take a closer look at the classic connection option. The essence of the above circuit is to connect the camera's power to the reversing light, the voltage at the terminals of which appears only after reverse gear is engaged. The connector (“tulip”) is connected to the standard output on the radio or screen intended for video communication. The excitation wire must be connected to the output of the radio, usually marked as “Reverse”. You can find out whether an excitation wire is required for your multimedia system from the technical documentation for the radio. At this point, do-it-yourself installation and connection for most cars can be considered complete.

Lamp fault monitoring system

What should you do if you have installed a rear view camera on your car, but it only works when the car is turned off? Many modern cars, usually of German origin, have a lamp monitoring system installed. The PWM controller sends rectangular positive pulses along the power wires of the lighting fixtures, which help detect burnt-out lights at the rear of the vehicle. Since the lamps have inertia, current ripples do not affect their operation. But the reversing camera will not work correctly with such interference.

To prevent this effect, the camera must be connected to the reversing light via a relay powered by the cigarette lighter (where the current will already be constant). In this case, “+” from the 3X lamps must be applied to the relay winding only after rectification with a diode and smoothing of ripples with a capacitor. The “minus” for powering the camera must be taken as far as possible after the “mass” of the 3X lights.

We invite you to watch the video from detailed description a way to eliminate interference so that you are guaranteed not to have problems with the picture on your car.

Today, a car is considered not a sign of luxury, but an ordinary means of transportation. If previously not everyone could afford such a toy, now almost all families have an iron friend in the garage or parking lot. If just ten years ago the music playing in the car showed the status of its owner, now this will not surprise anyone. After all modern technologies don't stand still. Every year they become more and more improved. Motorists just have to keep an eye on them. So, now an on-board computer or a rear view camera are very convenient devices that not only make life easier for motorists, but also reduce the risk of emergency situations and traffic accidents. A rear view camera (you can read how to connect it to the radio in this article) is a very convenient and practical device.

Installation locations

The rear security camera is a great device that helps any driver to perform quick and safe rear parking.

This product can be installed in many places on the car. For example, in the mirror or wherever your soul desires. However, everything is not so simple here. Be sure to keep in mind that to install such a camera you will need a special adapter or wireless module. However, do not forget that all signals will be transmitted with a slight delay - a few seconds. However, in real world even this can cost lives. Also, having another additional gadget in the car will concentrate your attention on it and distract you from safely driving a vehicle.

A rear view camera (you can find out how to connect it to a radio in this article) is most effective and comfortable if it is connected to a car radio.

It is best to entrust the connection procedure to an experienced technician. Carrying out such an operation does not take much time and is relatively inexpensive. However, if you really want to, you can do it yourself. The main thing before this is to carefully read the instructions and arm yourself the necessary knowledge and tools.

Carrying out preparatory work

The rear view camera (many drivers are interested in how to connect it to the radio themselves) is quite easy to install. The main thing is to understand the general principles.

Before connecting the unit to the radio itself, you need to install the camera correctly. The first thing you need to do is disconnect the positive terminal on the battery. This action is taken for safety reasons, in order to avoid a short circuit, which can subsequently lead to a fire in the car wiring itself. If you don't want to do this, you can simply disconnect the entire battery.

Trunk inspection

The rear view camera (how to connect to the radio is clearly described in this article, which means any driver can try to do it on their own) has wiring, so it is very important to decide where you will lay it. Open the trunk and choose the best place for it. It is best to run the wires along the already laid wiring. But it’s best to attach the camera eye above the license plate or directly to the bumper. Experts advise not to install a camera on the rear window inside the car. In this case, the picture will turn out very unclear.

Please note that you will have to worry about wires in the front part of the cabin. Therefore, disassemble several panels in order to gain access to the car's electrical wiring.

Under what conditions will the device work?

Please note that connecting the rear view camera to the radio has certain nuances. Keep in mind that the device will only receive power if you return it. The rear view camera differs from the recorder camera in the length of its working time. If the second device can work continuously, then the first one can work for a maximum hour. After this it will turn off. In principle, this is logical. After all, the main purpose of purchasing such a device is to create simplified conditions for parking, and not for full-fledged driving.

You have every chance to organize a wonderful tandem radio and rear view camera. But before that, make sure that your car radio is equipped with a special LCD screen. After you have completed all the preparatory operations, you can safely begin the connection process itself.

Tools required for work

In order to connect a rear view camera (Chinese radio or any other), you need to prepare some tools in advance. Namely:

  • scotch tape or insulating tape;
  • screwdriver;
  • glue or sealant;
  • keys and screwdrivers;
  • fuse 0.5 A;
  • Sometimes a soldering iron comes to the rescue.

First stage of installation

In order to connect a rear view camera to the Pioneer radio, you first need to install the observation peephole itself. This is done the same for all cars. In modern cars, “seats” are specially equipped for these purposes. If you find such a hole in your car, then it will be enough to remove the pre-installed plastic plug from it and insert the video sensor you purchased.

If your iron friend does not have such a hole, do not be upset. You can do it yourself. An electric drill or drill will come to your aid.

After you drill the appropriate hole in the car bumper, insert the camera “eye” into it, securing it with glue or sealant.

Now you need to correctly route the wires from the video camera itself into the trunk. At the same time, take the black wire and stretch it to the ground of the car. This is very easy to do with just a regular bolt. The positive red wire must be powered from the cable belonging to the rear light. And under no circumstances forget to connect the yellow wire to the camera itself.

When connecting the camera to the rear light, do not forget to use the fuse prepared in advance.

The process of connecting to the radio

After all the work with the peephole itself is completed, you can try to connect the rear view camera to the Pioneer radio. Continue to pull the cable from the trunk into the passenger compartment, securing it with tape or tape. Try to carry out this action in such a way that the yellow wire does not get pinched anywhere and does not get caught in the fasteners. Usually, a maximum of three to five meters of material is enough to complete all work with cables; a diagram will help you do the job correctly. Connecting a rear view camera to the radio will be much easier with its help.

Checking and setting

After completing all the work, you can connect car battery and start the car. Now engage reverse gear. If a certain image appears on the screen, it means that you have completed all the work absolutely correctly. If not, then experts recommend doing the following:

  • go to the radio settings;

  • select the “Camera” section;
  • adjust all its parameters.

That's all. The installation process is complete, which means you can enjoy the work you did in vain.

A great way to make reversing easier when parking is to install a rearview camera. This will greatly facilitate the parking process for beginners, as well as experienced ones in densely populated cities. But, it is still recommended to learn without parking sensors. The video broadcast while the car is moving in reverse can be displayed on the rearview mirror or on the car radio screen, or on a separate screen.

Types of rear view cameras for cars

Cameras can be divided into types and types according to the method of installation, according to the method of displaying, according to price category, by rating and demand.

Classification of cameras by display method:

    • wired;
    • wireless.

Classification of cameras by rating and demand:

      1. Sony (Sony). Wired Sony rear view cameras from 2 to 5 thousand rubles. Wireless ones cost from 20,000 rubles.
      2. MyDean (May Din).
        • MyDean VCM-300C. You can buy it for 2600 rubles.
        • MyDean VCM-381C. You can buy it for 2700 rubles.
        • MyDean VCM-363C. Price about 3000 rubles.
        • MyDean VCM-424C. Price about 4300 rub.
      3. Intro.
        • Intro VDC - 084.
        • Intro VDC - 103.
      4. Avis (Avis). Particularly suitable for trucks and buses.
      5. Pleervox (Pleervox). The cost is about 10,000 rubles.
      6. Karkam. The price is around 10,000 rubles.

You can purchase the camera either separately or as a set with everything you need (wires, connectors, screen). If you take a separate camera, you will have to display it on the radio screen if it supports video output, or you will also have to purchase a separate screen.

Rear view camera installation

Cameras can also be divided according to their installation location. Some cameras are mounted in the bumper, some above the license plate.

There are several places to install the rear view camera:

  1. In the license plate light. With this method, the camera must be installed so that the room lighting is not blocked.
  2. In the trunk handle. Some cameras can be secured to the handle with ordinary self-tapping screws.
  3. On the license plate frame. When installing a camera next to a number, a problem may arise such as camera flare, due to which the light will interfere with filming.
  4. In the bumper. You can install the camera without removing the bumper. Cameras in an oval body are better suited for installation in a bumper.

Additional equipment for rear view camera

Depending on the installation location and the weather, the camera can become dirty very quickly, rendering it useless. Dirt and ice quickly cover the camera lens. Only some cars have a standard function - a rear view camera washer.

There is additional equipment for the camera - this is a backlight. But, as practice shows, the backlight is blinding and the video is of poor quality.

You need to train yourself to park correctly, because an incorrectly parked car can interfere with others and costs from 1,500 to 5,000 rubles.

Wires and connectors

During installation, all connections must be well insulated. To avoid fractures as a result of frequent bending of the wires, they should be wrapped with rag tape and tied to standard ties so that they do not dangle. Inside the car, wires can be laid along the bottom, under the thresholds, and under the ceiling trim.
If a beginner can install a rear view camera with his own hands without much difficulty, then you need to be careful with the connection. If it’s a set of a camera and a rearview mirror, then yes, anyone can connect it without any problems.

For high-quality video transmission to the screen, you need to take into account the characteristics of the wires:

  • two-core wire for powering the camera itself;
  • two-core wire for transmitting images to the screen.

Video is transmitted to the monitor via an RCA connector (the so-called tulips or bells). For some rear view camera (RCC) connection options, the excitation wire will come out of the RCA connector. It is needed for high-quality video broadcasting.

The excitation wire supplies positive current to the radio screen and the system automatically starts recording video. Some multimedia systems do not have an excitation wire. There, the camera automatically turns on via the video link.

If the radio does not have this function, you will have to switch to video camera mode manually.

Connection diagrams

The camera can be connected using wires or wirelessly. For wireless transmission A special module is required. The module's power supply is connected to the reversing lamp, then the power goes from the module to the camera. And the second wireless module is connected to the monitor’s power supply. This method is not suitable for radios that have an excitation wire.
The classic wiring diagram for a rear view camera is to connect power to the reversing light. Voltage in which appears after turning on the reverse gear on the gearbox. The tulip (bell) connector is connected to the standard output on the radio itself or the screen for displaying video. The excitation wire must be connected to the output on the radio (usually marked Reverse). You can find out from the radio data sheet whether an excitation wire is required for this system.

Possible malfunctions after mounting and connecting the camera

It happens that after installing and connecting the KZV, the camera only works when the engine is not running. Some cars have a lamp failure monitoring system. The PWM controller transmits a signal to the batteries and calculates which light bulb has burned out. If there is a burnt-out lamp in the car, the rear view camera will work intermittently.

To avoid such problems every time a lamp burns out, the camera must be connected to the reversing lamp through a relay (regulator relay) with current from the cigarette lighter. The current in the cigarette lighter is constant. The negative for the reversing camera must be connected as far as possible from the ground of the reversing light. And the “+” from the reversing lamps is supplied to the relay coil.

Video

How to properly connect a reverse camera.

This video shows how to connect the camera yourself. The camera was purchased from Aliexpress.

Installation and connection of KZV.

Installation of a rear view camera with a mirror.

Once upon a time, not everyone could become the owner of a car, and if music could be heard from the open windows of the car, then its owner was considered a successful person earning crazy money. Today, a personal car is not a symbol of luxury, but a convenient means of transportation that almost every family has. Technological progress continues to simplify our lives and now a radio with a rear view camera, packtronics or a “smart” on-board computer does not surprise anyone. These tools help reduce the risk of a collision on the road or while parking to almost zero.

Rear CCTV camera is considered to be the best tool for quick or difficult parking. It is usually installed above the license plate and connected to the screen in the car. The car monitor for the rear view camera can be integrated into the mirror or be independent. The last option is not very convenient for several reasons. Firstly, to connect the camera you will need a wireless module or a special adapter with an RCA connector. In this case, the signal will be triggered with a delay of 2 seconds. Secondly, having another gadget in the car is not pleasing to the eye. That is why now more drivers prefer to connect a video device to the car radio.

Connecting a rear view camera with your own hands in this case is not difficult, but if you doubt your skills, then contact a car service center, where this service will be inexpensive. If you still want to do everything yourself, you will first need to prepare.

Preparing to install a rear view camera

In order to connect the device to the car radio, you will first need to install the camera itself. Therefore, the first step is to disconnect the positive terminal on the car battery. This is done as a precaution to avoid short circuits and subsequent fires in the wiring. Or simply disconnect the entire battery.

After that, look in the trunk and determine where the camera wiring will be located. Usually the wires are pulled along existing ones. The “eye” itself is most often mounted in the bumper or above the license plate in its backlight or in the license plate frame itself. In the front part of the cabin, several panels also need to be removed. For example, you will have to disassemble the dashboard and dashboard so that you have access to the electrical wiring.

Advice! It is not recommended to install a camera inside the passenger compartment on the rear window, as in this case the picture will be “blurry”.

Power to the camera comes from the reversing light, this necessary condition, so that the device turns on as soon as you start to back up. The fact is that rear view cameras, unlike DVR cameras, can operate for no more than 1 hour at continuous operation, after that they should turn off. This is quite logical, because the main purpose of these devices is to provide visibility while parking, and not while driving the car.

If you want to organize a tandem in which the radio will interact with the rear view camera, then it will not be superfluous to make sure that the audio device is equipped with the necessary LCD monitor.

When all the preparatory work is completed, you can proceed to installation.

Installing a rear view camera

Regardless of where the cameras are mounted, almost all of them are connected according to the same principle. To work you will need:

  • screwdriver;
  • fuse 0.5 A;
  • perhaps a soldering iron might come in handy;
  • screwdrivers and keys;
  • sealant (can be replaced with glue);
  • insulating tape (can be replaced with regular tape).

At the first stage of installation, the camera “eye” is installed. Some cars have seats for them. If there is such a hole, then you need to remove the plastic plug from it and simply install the video sensor there. If seat no, then a prepared drill or electric drill will come to your aid, with which you can make the necessary hole in the bumper. After the “eye” has taken its place, it must be fixed with glue or sealant.

Next, we pull the wires from the camera into the trunk and connect the negative wire (usually black) to the ground of the car. This can be done using any bolt. Power the positive wire (it's usually red) from the rear light power cable. Also remember to connect one end of the yellow wire to the camera.

Important! When connecting to the tail light, a 0.5 A fuse must be used.

At this stage, we figured out how to install a rear view camera on a car, now it’s time to connect it to the radio using a video cable.

Connection to radio

Once you have connected the camera to the car's electrical outlet, run the video cable (yellow tulip plug) through the interior and secure it with electrical tape. It is important that the yellow wire is not pinched and does not get caught in the fastening element. Typically, the length of the video cable is from 3 to 5 meters, this is enough to lay it in the most inconspicuous way even in a large SUV.

Healthy! If you do not have enough cable length, you can extend it with another cable of the same type.

Next, connect the cable to the tape recorder. To do this, first read the instructions for the radio, although the principle is the same for most systems, some may still differ in their configuration. Also in the document you will find the specification of the ports, their markings and the location of the input connectors. Usually it is enough to connect the second end of the “tulip” to the corresponding “Video in” connector.

A typical camera connection diagram is presented above. On most car radios that have the function of connecting a video camera, in addition to the video input, there is an additional wire for activating the inclusion of the radio in the mode of displaying the video image coming from the video camera. This wire is designated “Reverse” or “BACK”. Activation is carried out by applying a “positive” (+12 V) voltage to this wire. For this purpose, video camera manufacturers complete their products with a special wire that, in addition to the cores transmitting the video signal, has another core (red, designated “P3” in the diagram). One end of this wire is connected, together with the + 12 V end of the “P2” connector, to the power wire of the reversing lights, and the other end to the additional wire of the radio.

If we are talking about a wireless camera, then the connection principle is the same as described above, with one difference - instead of a yellow video cable, you will need to connect the included transmitter to the “Video in” port. This completes the installation of the rear view camera, the video of which you can watch at the end of the article. But don’t rush to assemble the interior trim; first you need to check that you did everything correctly.

Checking and setting up the camera

In order to check how successfully the installation and integration of the camera into the radio was completed, connect the battery, start the car and put the car in reverse gear. If an image appears on the car radio, it means you did everything correctly. If the picture is missing or is poorly displayed, try the following:

  • go to the radio menu in settings;
  • find the “cameras” section;
  • find the camera in the list;
  • adjust the focus and other parameters of the “eye”.

Thus, the car radio with navigation and rear view camera are installed and you can enjoy all the conveniences of this gadget.

In custody

When installing any new equipment that involves connection to the on-board power supply system, use fuses. This way you can avoid the unpleasant consequences of incorrect installation. Fuses should be selected based on the power of the device you are installing. Take your time, carefully secure the wires and their connections with electrical tape, then your video system will work smoothly for a long time.

The last thing a driver wants is to damage their car while parking on a busy street. Especially if it's someone else's car.

Indeed, no matter how experienced the driver is, there will be an unnoticeable little thing that will cause trouble. In such a situation, a rear view camera comes in handy. It significantly improves visibility and avoids unpleasant incidents.

Today, many cars are equipped with this useful gadget, especially in the premium segment. But early models lack this function, which means there is a reason to pick up the tool.

Today we will talk about how to connect a rear view camera to a Chinese radio.

How to choose a system

The automotive electronics market is abundantly filled with a variety of connection kits. This is especially true for products from China.

Indeed, for some owners, the quality of the transmitted picture or backlighting in the dark is not at all critical. Therefore, it is not worth paying money for unused features.


To better understand the presented devices, you need to understand the basic parameters. These include:
  • Video recording resolution. The higher this parameter, the better quality the video appears on the screen. Cameras with high resolution They convey in detail a picture of the smallest objects behind the car.
  • Matrix sensitivity. Sometimes this parameter is indicated by the “ISO” symbol. Cheap models are not equipped with sensitive matrices, this directly affects the image quality in the dark. The picture turns out fuzzy, it floats while moving.
  • Shooting coverage. The standard viewing angle range is 120-180 degrees. High rate helps make the video panoramic, allowing a large amount of space to fit into the frame. But there is an insidious point here: at such angles the real sizes of objects are distorted, which can deceive an inexperienced driver. Therefore, the optimal solution should be sought between these values.
  • Camera body and installation type. Waterproof devices can be safely installed outside the car; they are not afraid of water and dirt. But they will always be available to thieves. Cameras for internal installation are installed in the luggage compartment. The space coverage will be reduced, but the device will always be dry and protected from the wrong hands.
  • Connection type. The standard is a wired connection. A cable is laid from the monitor or radio to the rear of the car. More unusual is the wireless connection. The driver does not need to remove the trim and hide the wiring. But this method requires additional accessories - transmitters.
  • Rear cameras with backlight function. Using such devices you can easily navigate in the dark. Illumination is performed using infrared diodes or an additional lamp. This function is useful for those cars in which the rear lights are small in size and produce weak light. Whether this type of camera is needed is up to the owner to decide individually.

It is also necessary to pay attention to the way the image is displayed. This can be a separate monitor or a 2din radio with a built-in screen. If the quality of the latter is satisfactory, there is no point in installing a second monitor.

How to connect a camera to a radio with your own hands

Initially, you need to select an installation location. There is enough space in the rear of the car, but if you take into account the coverage of the broadcast picture, the choice is reduced.

It is worth considering the location of the camera eye. It must have a view of the entire shooting angle and not be obscured by other body elements.

There are two installation options: under the license plate and under the rear window. Here it is worth considering the type of car body. For station wagons, due to the lack of a long trunk, both methods are suitable. For sedans, the optimal location is in the license plate compartment.

Let's move on to the connection. Before starting work, you need to prepare the tool:

  • the camera kit itself with wires;
  • screwdriver;
  • a set of keys;
  • pliers;
  • plastic ties;
  • electrical tape or heat shrink tubing.

Sometimes for fastening rear camera You may need to drill several holes. In this case, you should stock up on drills and drills. Some car models have a prepared place for the camera, for which you just need to remove the factory plug.

Prepare the car interior for wiring. Carefully remove the upholstery. Choose places where the cable will not experience deformation from the feet of passengers, and also avoid sharp bends of the wire. It will be reliable to strengthen the wire on the standard highway of the car. Secure the line with plastic ties.


Let's move on to connecting the rear view camera to the Chinese 2din radio. To get to the ISO connections and the rear of the audio system, you need to carefully open the front panel (or several, depending on the car) of the dashboard and unscrew the mounting screws. The standard radio can be detached.

Tip: For the safety of the machine's electrical circuits, all connections should be made with the battery disconnected. This eliminates the risk of an accidental short circuit to ground.

Connection diagram of the camera cable connectors to the car radio

When the preparatory work is completed and the cables are laid, you can proceed to connecting all system components.

Let's take a closer look at the diagram:

The standard connection cable consists of two parts:

  • yellow – signal;
  • red – food.

Please note that the colors of the voltage wires may differ on different models.

The video signal connection is made through tulip-type connectors.

The standard method of powering and activating the camera is through the reversing lights. The operating principle is as follows:

  • The red wire is connected to the lights, the black wire is connected to the ground of the car.
  • The signal cord is connected through the trunk in the cabin to the radio via the Video In connector.
  • When reverse gear is engaged, voltage appears on the power wire of the camera, which activates it.
  • The radio detects a signal on the input channel and switches to image broadcast mode.

Very often, the connection to the radio is made through the ISO connector. In this case, you should familiarize yourself with the connection pins and find the video input.

The second connection method allows you to activate the surveillance system regardless of reverse gear. To do this, 12V is supplied to 2 wires - red and blue. The first one is connected to the ignition switch, to the key1 position – ACC. The second is connected to the reversing lamps.

With this method, the system will operate in two modes:

  • when shifting into reverse gear;
  • in the key positions key1 and key2 – Ignition, which corresponds to the on-board power supply being turned on and the car ignition.

Some radio models require manual activation of the shooting mode in the “settings” of the device. After activation, you should check the operation in different key positions, especially in key2.

The next step is to configure the radio itself, namely focus, sharpness and light sensitivity. Different systems offer a different set of settings, so configurations are individual.

Tip: It is important to observe strict correctness when connecting wires. To avoid mistakes, it is recommended to assemble the system on a table and configure it. When connecting power components to the vehicle network, protect them with fuses.

Connecting a car reverse camera to a laptop

To be able to view the picture on a laptop, you need a special TV tuner. With its help you can match an analog signal with a computer.


The connection principle remains unchanged. A 12V voltage is supplied to the power wires, and the video signal tulip is supplied to the tuner. The shooting is controlled through the software.

There are models on the market for dual-zone monitoring of the vehicle space - front and rear. This solution allows you to register possible emergency situations on the road, and record the condition of the car in the absence of the owner.

Connection and configuration are carried out in the following order:

  • the on-board network of the machine is de-energized;
  • the front camera is installed on the rear view mirror holder;
  • install the rear one;
  • for an aesthetic appearance, the connecting wires are connected to the head module under the interior trim;
  • if the standard radio has two Video In inputs, connect the signal wires to them. In the case where the kit has its own recorder, select the location for its installation, connect it to the network and cameras;
  • check the connections according to the installation diagram, turn on the battery;
  • configure camera operating parameters.

All that remains is to test the system in motion and, if necessary, make adjustments.

Sometimes it happens that one of the cameras does not provide adequate coverage of the space in front of it. The solution is to purchase a “Fish Eye” overlay. It acts as a wide-angle lens and expands the viewing angle.

The method of connecting such a mirror is no different. The connection diagram looks like:


Often, sets of mirrors with cameras can take power from the cigarette lighter through its own connector. The owner can choose which voltage supply method suits him best.

More expensive mirror models support shooting from both sides of the car. The front camera is already integrated into the body of the product and does not require connection.

Lovers of high-quality audio systems, Japanese equipment. But they have their own nuances when connecting video cameras.

Let's look at an example on a Pioneer radio, 2din format. The installation has a similar procedure:

  • The camera is powered by the reversing light.
  • The signal cable is connected to the Video In connector. Typically, in this model, a brown tulip is responsible for capturing video.
  • We check in the settings whether the camera is turned on and how it works.

The system works, but automatically; it will not turn on when driving backwards. It is enough to connect the purple wire of the head unit to the rear light, where the camera is. The problem will be corrected when reverse gear is engaged. The radio will understand that you need to activate the shooting mode.

The remaining aspects of installing the device remain the same.

Conclusion

Rear or front cameras have proven themselves with the best side among car enthusiasts. With their appearance on board the car, it becomes easier to navigate in cramped spaces. Their correct installation requires the owner to have some knowledge. But with the tips given, any driver can do this.

 

It might be useful to read: