Siz for plumbing norms. We choose clothes for plumbers and household repairmen. High-quality special clothing from a trusted manufacturer

On the shoulders of a locksmith often lies the need to perform a number of work tasks. Throughout the entire time of work, the locksmith must be protected from a variety of threats - mechanical shock, excessive humidity, hypothermia and others. When choosing special clothing, its set itself can vary greatly and depends on the specific working conditions.

A set of overalls for locksmiths

Overalls;
Boots;
Jacket.

The composition of the kit may vary, depending on the industry in which the locksmith is engaged. The kit can be supplemented with helmets, respirators, goggles and other elements. Depending on the field of work, the requirements for the fabric also change. In particular, when working in a car service, the employee must be well insured against sparks, oil and various kinds of combustible substances. For plumbers, the main requirement for a set of clothing is protection from moisture and condensation.

A high-quality set of clothes must certainly be made of durable, easy-to-clean fabric. Overalls for locksmiths are sewn in such a way as to be as comfortable as possible to wear and not restrict movement.

High-quality special clothing from a trusted manufacturer

Our company offers its customers high-quality, strong and durable special clothing for locksmiths. Tailoring of workwear is carried out by professionals in their field with a choice of optimal fabrics, adapted specifically for workers in the chosen industry. The catalog is presented as

Traditionally, the customer side of power generation has not attracted much attention. Today's customers use rooftop solar, residential wind power, fuel cells, microturbines, residential solar and many other energy sources.

Underwater network

There are underwater power cables for thousands of kilometers on the seabed, so why not connect the electrical network there as well? Such an idea has come up periodically over the years, when oil rigs, gas platforms and wind farms have appeared offshore.

Too many SPPs and WPPs increase the cost of the energy system

If solar panels and wind turbines keep getting cheaper, why build anything else?
As the number increases solar panels and wind farms, their overall performance is declining. The cost of an individual solar panel is low, but when there are many of them, the cost of the entire system is quite high.

US switchgear market

Since the global electricity market has adopted an AC rather than a DC system for the transmission and distribution of electricity, switchgears serve as the backbone of electrical networks.

Decarbonization with renewable gas

One way to decarbonise the electrical grid is to use renewable hydrogen, i.e. hydrogen produced from renewable energy sources. The process is the use of wind and solar energy in a period to create hydrogen through electrolysis, and then burning renewable hydrogen in gas turbines when energy is required in the network.

DER platform supports home energy storage

The integration of Sunverge's advanced platform with LG's energy storage system will provide advanced consumer and network services for customers and utilities.

Network management flexibility: batteries

With considerable uncertainty about the role that batteries will play in power grid management, how should grid operators and utilities position themselves to respond to market changes?

Utilities are accelerating their move to the cloud

Improved customer experience has been identified as a key factor in increasing investment in the cloud.

What we don't hear from the media about global climate shocks

Since 1990, greenhouse gas emissions from the electricity and industry sectors have declined, while emissions from the transport and residential sectors have increased.

Hydrogen, an important step towards independence from fossil fuels

With hydrogen produced from renewable sources such as wind power, much of today's carbon emissions associated with industry, transport and heating can be avoided.

How energy can manage risk

Electricity executives must devote time and resources to improving their digital risk management practices.

Switching and durability of low-voltage circuit breakers

The factors of durability of operation of low-voltage circuit breakers (how long the contacts will last) in connection with switching operations are considered.

cross stitching effect

XLPE is the recognized abbreviation for cross-linked polyethylene. This one and others synthetic materials cross-linked rubber, of which ethylene propylene rubber (ERP) is the most notable example, are increasingly being used to insulate cables over a wide voltage range.

When a customer complains that the equipment is damaged due to voltage deviation

While voltage fluctuations and momentary power outages cause the most common power quality problems, there are other causes of equipment failure and malfunction.

Electrical maintenance management 4

Based on an evaluation of the various factors discussed earlier, and an evaluation of other factors, if any, a decision is made to implement a condition monitoring service. How exactly this program can be implemented in practice is discussed below.

The impact of any equipment maintenance initiatives, including condition monitoring, should be predictable and measurable, and related to the performance and reliability of the production unit. In addition, it should be remembered that monitoring systems, especially fully integrated technologies, are themselves subject to failures and failures, and require maintenance.

Electrical maintenance management 2

A predictive maintenance management program is a maintenance program created for electrical equipment based on regular monitoring of its actual physical condition, operating parameters, operating efficiency and other indicators. A condition-based maintenance management program consists of techniques that attempt to "predict" or diagnose problems in electrical equipment based on the analysis of received data.

Electrical maintenance management 1

Over the past two decades, the concept of equipment maintenance has taken on different dimensions and has changed to a great extent, perhaps more than any other management discipline. Electrical equipment, which has a rather complex design, requires new methods of maintenance, and a change in views on the organization of maintenance and the responsibility associated with it.

What to consider when choosing a location for a substation

At the stage of choosing a place for an electrical substation, it is necessary to determine the place that the future electrical power substation will occupy, including the placement of its main equipment.

The role of medium voltage distribution equipment

Since for the transmission of electricity, and for its regional distribution, different levels high voltage, then, due to the wide variety of requirements and tasks of distribution equipment and substations, the term "medium voltage" began to be used.

From the beginning of 2017, enterprises paying in the Social Insurance Fund will be able to compensate for the costs of purchasing safety shoes, overalls and other personal protective equipment (PPE) through injury contributions.

Moreover, only the cost of overalls made in Russia and from Russian materials is subject to compensation.

Legislative acts

Order of the Ministry of Labor of the Russian Federation No. 201n dated April 29, 2016

The order amends another order, No. 580n dated December 10, 2012, on financial support for measures to reduce injuries and occupational diseases. These documents, in addition to PPE, regulate the procedure for applying for the allocation of funds for other similar purposes:

providing workers with therapeutic and prophylactic nutrition (milk);
provision of vouchers for sanatorium treatment for such employees;
holding;
purchase of first-aid kits, and for transport companies - tachographs and breathalyzers;
training and retraining of specialists in ;
assessment of working conditions and;
other similar events.

PPE is reimbursed only if the issuance complies with standard standards and is provided free of charge to employees.

The insured will need to prove:

compliance of certified workplaces with working conditions and professions for which the provision of PPE is required;
compliance with PPE technical regulations Customs Union"On the safety of PPE" No. 878 dated 12/09/2011;
compliance of all PPE with the issuance standards.

The norms for providing PPE, the requirements for their acquisition, issuance, storage, care are contained in the Order of the Ministry of Health and Social Development of the Russian Federation No. 290n of 06/01/2009.

Order of the Ministry of Health and Social Development No. 290n of 06/01/2009

The order contains general cross-sectoral rules that apply to all employers, as well as the definition of PPE - strictly individual protective equipment that are intended:

for protection against pollution or temperature conditions;
to reduce the degree of impact on working harmful factors.

The employer is required to provide appropriate PPE free of charge, according to the employee's personal characteristics and as often as required by the regulations.

It is acceptable to draw up a lease agreement and for temporary use. Products must be certified. The employee must be notified of the norm applicable to his position.

Priority in providing, according to the order, belongs to industry standards for the type of activity of the enterprise, and for workers of cross-cutting professions that exist in many enterprises - according to standards for types of work.

Cross-cutting professions and general criteria for issuance

By order of the Ministry of Labor of the Russian Federation No. 997n dated December 9, 2014, the norms for issuing a year for a list of 195 cross-cutting professions were established.

In addition to the list of professions, there is a list of working conditions under which all employees are subject to protection, and the service life of overalls depending on the climatic zone of operation.

Drivers trucks, tractors and truck cranes are required:

one suit;
6 pairs of gloves with polymer coated.

Gas welder, electric gas welder, electric welder, welder of fittings, plastics:

a suit that protects against splashes of molten metal;
two pairs of leather boots that protect against sparks and elevated temperatures;
two pairs of leather boots to protect against sparks and elevated temperatures;
duty dielectric gloves, boots, rugs;
6 pairs of resin coated gloves, 12 molten splash proof gloves, spot sprayed gloves as they wear;
protective heat-resistant shield (welder mask) with a light filter or glasses with similar characteristics;
goggles, respirator - to wear.

Storekeepers and sellers non-food items issued under normal conditions, without exposure to hazardous substances:

two aprons with a bib;
monthly - gloves.

A veterinarian, a livestock breeder, a groom are provided with:

a suit or robe with trousers to protect against pollution;
an apron with a bib;
a pair of rubber boots;
once a quarter - with gloves.

Janitors or area cleaners receive:

anti-pollution suit;
two aprons with a bib;
rubber boots;
once every two months - gloves.

In addition to cross-cutting professions, model norms provide for the provision of employees of all industries:

climate-adapted overalls and footwear (Resolution of the Ministry of Labor No. 70 of December 31, 1997);
special reflective and signal clothing (Order of the Ministry of Social Development No. 297 of 04/20/2006).

In Russia, there are 4 classes of protection for outerwear and special footwear, depending on the natural and climatic features of the region (belt).

So, the clothes are designed for a comfortable stay outdoors in the winter months for two hours at average negative temperatures and average wind speed:

Protection class 4 is valid for the regions of the North and the Arctic (special belt), with a winter temperature of -25 ° C and a wind of 6.8 m / s;
class 3 (central Siberia, north of the European part of the country, Kamchatka, Sakhalin, Kuril Islands) with temperatures from -41°С;
2 class (south Far East, middle and southern Urals, southern Siberia, Udmurtia, Tatarstan, Karelia, Kirov region) temperature from -18 ° C, wind 3.6 m / s;
Class 1 (southern and middle European parts of the Russian Federation) temperature from -9.7°С, wind 5.6 m/s.

For a special climatic zone, for example, the issuance of:

a protective suit with an insulating lining (similarly, protective suits against
acids, fire, sparks) - for a year and a half;
a protective jacket with an insulating lining, insulated trousers - for a year and a half;
short fur coat and hat with earflaps - for three years;
moisture resistant felt boots and fur mittens - for two years;
boots and boots - for a year.

When dismissing employees, the employer must issue an order. You will find the form by which it is filled out.

Industry norms and regulations

Occupational safety specialists, who know the specifics of production in each industry, have developed a whole list of standards for the provision of PPE certain types activities and even holdings (Gazprom, Surgutneftegaz). All norms are approved by orders and resolutions of the Ministry of Labor and the Ministry of Health and Social Development of the Russian Federation. In total, about 70 such documents have been approved to date:

No. 416n dated 12.08.2008 - Agriculture, water management;
No. 68 of December 29, 1997 - fishing and timber industry, pulp and paper production, microbiology, pharmaceuticals;
No. 341n of 08/02/2013 - coal mines;
No. 61 dated 12/08/1997 - peat harvesting, woodworking;
No. 906n dated August 11, 2011 - chemical industry;
No. 652n dated November 1, 2013 - metallurgy;
No. 1104n of December 14, 2010 - mechanical engineering
No. 357n dated 06/22/2009 - vehicles and road construction.
According to order No. 1104 of December 14, 2010, PPE standards for machine operators were determined.

Turner, boring machine, grinder, miller:

anti-pollution suit;
leather boots with a protective toe cap;
mittens or gloves (for working with a beam crane);
aerosol respirator (when processing cast iron).

Order No. 357n dated 06/22/2009 defines the PPE standards for road workers:

Asphalt concrete worker (except winter season):

signal suit or overalls;
leather boots or boots with a protective toe cap;
goggles and a helmet with a balaclava;
canvas mittens or knitted gloves;
knee pads;
headphones or earplugs;
respirator.

In winter additionally:

signal suit with insulating lining;
waterproof signal coat;
insulated leather boots or boots.

For road works:

signal vest.

PPE issued to everyone specific employee, must correspond to his gender, height, size.

The employee must use PPE correctly. If the employee refuses to use overalls and protective equipment, the employer has the right to remove the person from work and impose

In addition to clothing, footwear and protective items, the regulations establish the provision of disinfectants and washing liquids (soap), protective hand creams. The issuance of all PPE is recorded in the employee’s card, the card in in electronic format confirm with links to a document that contains the signature of the recipient.

Caring for the health and safety of an employee in the process of work is not a right, but a duty established by the state by law. It is in the general interest to prevent, as far as possible, accidents and occupational diseases at work.

Notes:

1. The flight crew performing flight work on passenger aircraft of the 1st and 2nd class in a special climatic region is issued free of charge special clothing, special footwear and other personal protective equipment in accordance with these Norms.

2. To the commander of an aviation detachment and the deputy commander of an aviation detachment, the head of an aviation enterprise, the commander of an aviation detachment united with the airport, and their deputies for flight service, who occasionally perform aviation chemical work on the treatment of areas using pesticides, special clothing, special shoes and other means personal protective equipment is issued with an increase in wearing time by 30%.

3. To the head and deputy head, chief specialist, leading specialist of the territorial department of the special authorized body in the field of civil aviation, non-permanently performing control and inspection and training flights on aviation chemical work on the treatment of areas using pesticides, special clothing, special shoes and other means personal protective equipment is issued with an increase in wearing time by 40%.

4. The half mask with interchangeable cartridges is completed with interchangeable cartridges, the brand of which is determined by the results of certification of the workplace for working conditions.

Notes to subsection 1 of section I:

1. Commanders of aviation detachments, commanders of aviation detachments united with the airport, heads of the aviation enterprise and their deputies for flight service, flight commanders and flight inspectors of territorial departments and central office special authorized body in the field of civil aviation, special clothing, special footwear and other personal protective equipment are issued if there are valid certificates for the right to operate aircraft and their equipment and when they perform flight work to check piloting techniques and practical work air specialists:

on cargo turbojet, turboprop and class 3 passenger aircraft - in accordance with these Standards with an increase in wear time by 30%;

on class 4 aircraft and helicopters - in accordance with these Standards with an increase in wear time by 40%.

2. When performing temporary flight work in various climatic regions, the flight and cabin crew are provided with special clothing, special footwear and other personal protective equipment for the duration of work in accordance with the standards of the corresponding climatic region, regardless of the place of permanent deployment.

The flight crew of passenger turboprop and turbojet aircraft during flights to a special climatic region is also provided with special clothing, special footwear and other personal protective equipment in accordance with the standards provided for and these Standards for a special climatic region.

At the end of temporary work, special clothing, special footwear and other personal protective equipment must be returned.

3. The flight crew performing flight work on passenger aircraft of classes 1 and 2 in a special climatic region is provided with special clothing, special footwear and other personal protective equipment in accordance with these Standards.

4. The period of wearing special clothing and special footwear provided for a flight radio operator, senior flight engineer and senior flight engineer of an aviation squadron, navigator, navigator of an aviation squadron and senior navigator of an aviation squadron is increased by 30%.

5. When performing aerial work over the waters of the seas and oceans, as well as when performing flights to offshore drilling rigs, each member of the flight and cabin crew is given an additional wetsuit, a set of cotton underwear, a set of insulated underwear with wearing periods, respectively:

- "before wear";

1 set for 1 year;

1 set for 2 years.

This safety instruction for a plumber is available for free viewing and download.

The instruction on labor protection for a plumber was prepared on the basis of SP 12-135-2003 “Labor safety in construction. Industry standard instructions on labor protection”, containing industry standard instruction on labor protection - TI 130-2002, taking into account the requirements of the current legislative and regulatory legal acts containing the state regulatory requirements for labor protection specified in Appendix 1 and is intended for a plumber when performing work according to his profession and qualifications.

1. GENERAL REQUIREMENTS FOR LABOR PROTECTION

1.1 To perform the duties of a plumber engaged in the repair and maintenance of sewer and water systems and structures, persons at least 18 years of age who have passed:
— induction training;
- fire safety briefing;
- initial briefing at the workplace;
— training in safe labor methods and techniques for at least a 10-hour program (for work that is subject to increased safety requirements — a 20-hour program);
- briefing on electrical safety at the workplace and verification of the assimilation of its content.
1.2. The plumber must pass:
- repeated briefing on labor safety at the workplace at least every three months;
- internship;
— unscheduled and targeted briefings: when changing technological process or rules on labor protection, replacement or modernization of production equipment, fixtures and tools, changes in working conditions and organization, in case of violations of labor protection instructions, interruptions in work for more than 60 calendar days(for works that are subject to increased safety requirements - 30 calendar days);
- dispensary medical checkup.
1.3. The plumber must:
- comply with internal regulations work schedule installed at the enterprise;
- comply with the requirements of this instruction, instructions on fire safety measures, instructions on electrical safety;
- comply with the requirements for the operation of equipment;
— use for its intended purpose and take care of the issued personal protective equipment.
1.4. The plumber must:
- be able to provide first (pre-medical) assistance to the victim in an accident;
- know the location of first aid, primary fire extinguishing equipment, main and emergency exits, evacuation routes in case of an accident or fire;
- perform only the assigned work and not transfer it to others without the permission of the foreman or head of the shop;
- during work, be attentive, not be distracted and not distract others, do not allow workplace persons not related to work;
- Keep the workplace clean and tidy.
1.5. The plumber must know and follow the rules of personal hygiene. Eat, smoke, rest only in specially designated areas and places. Drink water only from specially designed installations.
1.6. If malfunctions of equipment, fixtures, tools and other deficiencies or hazards are found in the workplace, immediately inform the foreman or head of the workshop, work can only be started with their permission after all the deficiencies have been eliminated.
1.7. If a fire is detected or in the event of a fire:
- turn off the equipment;
- report to fire department and administration;
- start extinguishing the fire with the primary fire extinguishing equipment available in the workshop in accordance with the fire safety instructions.
If there is a threat to life, leave the premises.
1.8. In case of an accident, provide the victim with first (pre-medical) aid, immediately report the incident to the foreman or head of the workshop, take measures to preserve the situation of the incident (equipment condition), if this does not create a danger to others.
1.9. For non-compliance with the safety requirements set forth in this manual, the worker is responsible in accordance with current legislation.
1.10. In accordance with the Model Industry Standards for the free issue of special clothing and special footwear and other personal protective equipment to workers and employees, a plumber must use the following PPE in his work:
– tarpaulin suit – wear period 18 months,
- rubber boots - 12 months,
- combined mittens - 2 months,
- rubber gloves - on duty,
- hose gas mask - on duty.
For outdoor work in winter additionally:
— cotton jacket with insulating lining — 30 months,
- cotton trousers with insulating lining - 30 months.
Keep special clothes and footwear in closets, and take warm overalls in the summer season for storage in a warehouse. All overalls and footwear should be dried in the prescribed manner and handed over for washing and repair.
1.11. The main dangerous production factors under certain circumstances may be:
- faulty metalwork tool;
- ladders and brackets for lifting and descending into the well;
- random items used to open manhole covers of wells;
- electric current in case of damage to power networks during earthworks to open pipelines of the sewerage and water supply network;
- falling random objects, blank parts and tools;
- flammable and gas-air mixtures and toxic substances (methane, lighting gas, hydrogen sulfide, sulfur dioxide, ammonia, chlorine, etc.);
- malfunction of tools and equipment for harvesting pipes, spurs, couplings and other parts, lack of safety and protective equipment for a locksmith, poor lighting and cluttered workplace.

2. HEALTH REQUIREMENTS BEFORE STARTING WORK

2.1. The plumber must be aware that the performance of work on the repair, inspection and prevention of sewer and water wells, pits, tanks and structures are high-risk works, and therefore they must be carried out by a team of workers of at least 3 people after receiving instructions on labor protection and permit for the production of work.
2.2. Before performing work in wells, a mechanic must put on serviceable overalls and footwear, a protective helmet, and also receive safety belts with a rope, which should be 2 meters longer than the depth of the well, have knots along the entire length at a distance of 250-300 mm and is checked for rupture with a load of 200 kg, get gas analyzers or gas indicators, a 12-volt battery torch, a hand fan, fences, posters of the established sample, hooks and crowbars for opening covers and hatches of wells, buckets, tools. All funds received for work must be checked for their serviceability.
2.3. Install at open wells, pits the necessary fencing, warning posters and road signs. At night, hang lanterns with red lenses on the racks of signal signs.
2.4. Check the serviceability of the brackets or ladder in the well, 6-8 hours before the start of work, open the manhole covers of two adjacent and working wells to ventilate them.
2.5. Take measures to turn off the pipelines leading to the sewer devices and hang out posters in places of disconnection with the inscription: “Do not turn it on - people are working!”
2.6. Using a gas analyzer or gas indicator, check and make sure that there are no gases at the bottom of the well (methane, carbon dioxide, sulfur dioxide, and other gases).
2.7. Prepare the tool, as well as the blanks of pipes, spurs, couplings necessary for the work.
2.8. Check the necessary tools and fixtures for work and make sure they are in good condition:
2.9. Handles of hand tools should be smooth and oval, files, rasps, etc. with a pointed working end should be fixed in a smooth, smoothly polished handle, tightened at both ends with metal bandage rings, chisels, cross-messels should not have damage on the working part in the form of sharp ribs in the places of gripping by hand, cracks and burrs in the back of the head, used wrenches wrenches must match the dimensions of the bolts and nuts. It is not allowed to lengthen wrenches by fitting gas pipes or extending a second wrench, bench vise must be with strictly parallel jaws and equipped with soft metal gaskets (copper, brass, etc.).

3. HEALTH REQUIREMENTS DURING WORK

3.1. When working on a grinding machine for the preparation and processing of pipes, spurs, couplings, etc. make sure that the distance between the edge of the handpiece and the working surface of the abrasive wheel is no more than 3 mm, the machine must be equipped with a protective screen.
3.2. Installation and maintenance of pipes and fixtures of sanitary systems at a height of more than 1.5 meters is allowed from scaffolding and scaffolding installed on a solid foundation. It is not allowed to install scaffolds on random supports (barrels, bricks, pipes, heaters, etc.). After installation and repair of systems, check the tightness of threaded and bolted connections.
3.3. When performing work together with an electric welder, the locksmith must wear protective equipment (dark glasses, gloves).
3.4. Pipe blanks and other products should be laid so that they do not block passages and do not interfere with work.
3.5. Work in wells, pits should be carried out by a team of locksmiths of 3 people, one of whom is inside the well, the other on the surface, and the third must perform the work of observing the worker inside the well and, in case of poor condition, provide the necessary assistance. It is prohibited to engage the observer in any work before the worker in the well, tank, structure comes to the surface.
3.6. Lower into the well and raise from it any objects, tools, Construction Materials should be in a bucket using a rope, cable. The worker who is at this time in the well should step aside. All tools and other items must be removed from the hatches of the well.
3.7. While working in a well or channel, the gas indicator, which determines the presence of gas, should be near the worker at the inlet pipe, and if gas enters the well, work should be stopped and the worker should rise to the surface.
3.8. Lighting of the place of work should be carried out with rechargeable lamps or portable lamps with a voltage not exceeding 12 volts. The lamp must be protected by a metal mesh.
3.9. When working inside the sewerage network, it is forbidden to use open fire, smoke, use matches, lighters, etc. All this can lead to an explosion.
3.10. In cases where it is necessary to perform work, and for some reason the gas from the well cannot be completely removed or it is supplied, the mechanic must work in the well in an insulating gas mask with a hose that goes to the surface of the well (chamber). The duration of work in this case without a break should not exceed more than 10 minutes.

4. REQUIREMENTS FOR LABOR PROTECTION IN EMERGENCY SITUATIONS

4.1. In the event of emergency and other situations (sudden appearance of gas in the well, heavy rain, signs of weakness in the worker, etc.), work in the well should be stopped, and the worker should immediately be raised to the surface, in case of loss of consciousness, he should be given medical assistance .

5. REQUIREMENTS FOR HEALTH AND SAFETY AFTER THE END OF WORK

5.1. Tidy up the workplace, close the hatch of the sewer well, pits, remove fences and warning signs.
5.2. Remove the tool and all accessories in the place provided for them.
5.3. Take off overalls and shoes, put them in the place provided for them.
5.4. Wash face and hands with soap and water or, if necessary, take a shower.

Thank Sergey for this labor protection instruction 😉

It might be useful to read: