What does the chief metrologist do? Chief Metrologist. metrologist resume template


APPROVE

(name of the enterprise, organization, institution)

(head of an enterprise, organization, institution)

JOB DESCRIPTION

00.00.0000

№ 00

(signature)

(FULL NAME.)

Structural subdivision:

Department of Chief Metrologist

Position:

Chief metrologist

00.00.0000

  1. General provisions
    1. This job description defines the functional duties, rights and responsibilities of the chief metrologist.
    2. The chief metrologist belongs to the category of managers.
    3. The chief metrologist is appointed to the position and dismissed from the position in accordance with the procedure established by the current labor legislation by order of the director of the enterprise upon submission technical director.
    4. Position relationships:

1.4.1

direct submission

technical director

1.4.2.

Additional submission

Director of the enterprise

1.4.3

Gives orders

Employees of the department of the chief metrologist

1.4.4

The employee replaces

person appointed by the director of the enterprise

1.4.5

The employee replaces
  1. Qualification requirements of the chief metrologist:

2.1.

Education

higher professional (technical)

work experience

work experience in the field of engineering leadership positions for metrological support of production for at least 5 years.

knowledge

Legislative and normative legal acts, methodological materials on the metrological support of production.

Profile, specialization and features of the organizational and technological structure of the enterprise, prospects for its development.

The procedure and methods for planning work on metrological control and production support.

Organization of metrological support of production in the industry and at the enterprise.

Production capacities, technical characteristics, design features and operating modes of equipment, rules for its operation.

Fundamentals of production technology of the enterprise.

Regulations, instructions and other guidelines for the development and execution of technical documentation.

The device and rules for the operation of measuring instruments, the organization of their repair.

Methods for conducting research and development in the field of improving metrological support and measuring instruments.

The procedure for concluding contracts with third parties.

Fundamentals of economics, organization of production, labor and management.

Fundamentals of labor legislation.

Rules and norms of labor protection.

skills

Additional requirements
  1. Documents regulating the activities of the chief metrologist

3.1 External documents:

Legislative and regulatory acts relating to the work performed.

3.2 Internal documents:

Charter of the enterprise, Orders and instructions of the director of the enterprise (technical director); Regulations on the department of the chief metrologist, Job description of the chief metrologist, Rules of internal work schedule.

  1. Job responsibilities of the chief metrologist

Chief metrologist:

4.1. Organizes work on metrological support for the development, production, testing and operation of products manufactured by the enterprise.

4.2. Supervises the preparation of projects and plans for the introduction of new measuring equipment, organizational and technical measures to improve production efficiency, improve metrological support, means and methods of measurement, control and testing.

4.3. Ensures the compilation of local verification schemes, the establishment of the optimal frequency and the development of calendar schedules for verification of measuring instruments.

4.4. Leads the work on carrying out metrological examination of design and other technical documentation developed at the enterprise, as well as coming from other enterprises and organizations.

4.5. Participates in ongoing research on automation production processes related to the use of measuring instruments, in the work to determine the needs of the enterprise for these means.

4.6. Provides implementation modern methods and measuring instruments, as well as carrying out work on the assessment of measurement errors.

4.7. Organizes work on the analysis of the state of metrological support, carrying out metrological certification of non-standardized measuring instruments, development, coordination and approval of methods, instructions and other regulatory and technical documentation for their verification, as well as certification of measuring instruments after restoration, repair, verification.

4.8. Manages equipment technological process all the measuring instruments provided for by the regulations, the compliance of the measuring instruments and methods used in the divisions of the enterprise with the requirements for compliance with the specified production modes and product quality.

4.9. Issues instructions aimed at preventing, stopping or eliminating violations of metrological rules and regulations.

4.10. Organizes training terms of reference for the design and development of special-purpose measuring instruments.

4.11. Ensures the completion of the exchange fund of measuring instruments, testing and control, storage and comparison in the prescribed manner of working standards, repair and maintenance of samples of measuring instruments in proper condition.

4.12. Promotes the implementation of state and industry standards, enterprise standards and other normative and technical documentation regulating measurement accuracy standards, methods and means of verification.

4.13. Supervises the work on the preparation of the established reporting and its submission to the bodies of the state metrological service.

4.14. Organizes work to improve the skills of metrological service employees.

4.15. Supervises the employees of the enterprise who carry out metrological control and metrological support of production.

  1. Rights of the chief metrologist

The chief metrologist has the right:

5.1. Act on behalf of the department, represent the interests of the enterprise in relations with structural divisions enterprises, bodies of state metrological control and supervision, other bodies state power on issues of metrological support of production.

5.2. Make proposals to the head of the enterprise on the conclusion of agreements on the lease of unique measuring instruments and test equipment for calibration and other metrological work, as well as agreements on the involvement of third-party specialists in the metrological examination of documentation and metrological certification and the introduction of measurement methods.

5.3. Require the heads of structural divisions and independent specialists to provide information necessary to perform work on metrological control and metrological support of production.

5.4. Participate in the preparation of draft orders, instructions, instructions on the issues of metrological support of production.

5.5. Give instructions to the heads of structural divisions of the enterprise on issues of metrological control and production support.

5.6. Submit proposals for prosecution in the prescribed manner officials guilty of violating the rules for the use of measuring instruments, the procedure for metrological support of production.

5.8. Submit for consideration by the head of the enterprise:

5.8.1. Representations about the appointment, transfer and dismissal of subordinate employees.

5.8.2. Suggestions: to encourage distinguished employees, to bring to material and disciplinary responsibility violators of industrial and labor discipline.

5.9. Approval and sign documents within their competence.

5.10. Independently conduct correspondence with structural divisions of the organization, as well as other organizations on issues within its competence and not requiring the participation of the head of the enterprise.

  1. Responsibility of the chief metrologist

chief metrologistis responsible:

6.1. For improper performance or non-performance of their official duties under this job description, - within the limits determined by the current labor legislation of Ukraine.

6.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of Ukraine.

6.3. For causing material damage- within the limits determined by the current labor and civil legislation of Ukraine.

  1. Working conditions of the chief metrologist

The mode of operation of the chief metrologist is determined in accordance with the Internal Labor Regulations established in the enterprise.

  1. Terms of payment

The terms of remuneration of the chief metrologist are determined in accordance with the Regulations on remuneration of personnel.

  1. Final provisions
    1. This Job Description is made in two copies, one of which is kept by the Company, the other- at the worker.
    2. Tasks, Responsibilities, Rights and Responsibilities can be specified in accordance with the change in the Structure, Tasks and Functions of the structural unit and workplace.
    3. Changes and additions to this Job Description are made by order CEO enterprises.

Jobs chief metrologist vacancy chief metrologist in Moscow. Vacancy chief metrologist from direct employer in Moscow job advertisements chief metrologist Moscow, vacancies recruitment agencies in Moscow, I am looking for a job as a chief metrologist through recruitment agencies and from direct employers, vacancies as a chief metrologist with and without work experience. The site of announcements about part-time work and work Avito Moscow job vacancies chief metrologist from direct employers.

Work in Moscow chief metrologist

Site work Avito Moscow work fresh vacancies chief metrologist. On our website you can find high paying job chief metrologist. Look for a job as a chief metrologist in Moscow, view vacancies on our job site - an aggregator of vacancies in Moscow.

Avito jobs Moscow

Jobs chief metrologist on the site in Moscow, vacancies chief metrologist from direct employers Moscow. Vacancies in Moscow without work experience and highly paid with work experience. Vacancies chief metrologist for women.

(the profession of a metrologist should sound proud)

E.L. Perelshtein, former Ch. metrologist of the basic metrological service of Minaviaprom.

The article is devoted blessed memory two prominent organizers of the "measuring business" in the country, Kiparenko V.I. and Konorova L.A. in January 1965, the first conference on "Ensuring the uniformity of measurements in the national economy of the country", which marked the beginning of development in the country " State system ensuring the uniformity of measurements (GSI) ".

More than 35 years ago, the positions of Chief Metrologist, Engineer and Metrology Technician began to appear in certain industries. It soon turned out that such specialists are practically not trained anywhere - they must be "grown" on their own, based on work experience in related professions. At the same time, many enterprises began to form complex divisions for measuring equipment with the general name "Metrological Service", which were assigned certain functions for the preparation of methods and measuring instruments for reasonable use in the divisions of enterprises. The enterprises also saw the light of new concepts - "measurement technique", "metrological examination" and a number of others. But the most surprising thing was that short term In a number of industries, a whole galaxy of unstoppable enthusiasts, new chief specialists of enterprises - Chief metrologists, has indeed grown. It is difficult to say where they all came from so quickly and immediately got their bearings in the tasks assigned, but we must give them their due - the work literally began to boil. But many of them did not even have close contact with measuring equipment before. Probably the combination of youth and novelty of activity, as well as a sense of perspective in the assigned work, inspired the new chief specialists to solve still unexplored metrological problems. Metrological excitement, in some cases, captured the entire enterprise. Units involved in measuring equipment were united - verification and repair, development of non-standardized measuring instruments. Calibration installations were purchased, personnel were selected, their studies and certification were organized for the right to carry out calibration work. Sectoral and intersectoral councils of Chief metrologists were formed, meetings and conferences were convened, work was carried out daily to provide mutual assistance to solve operational tasks and problems. There was a fierce struggle for premises, for numbers and wages for the metrology departments. Metrological life was born at the enterprises. The necessary resolutions were issued and decisions were made for the development of measuring technology and instrumentation by almost all branches of government. It was clear that the ideas of the unity of measurements lay on fertile ground.

It is hardly possible to deny the outstanding contribution that was made by the metrological services of enterprises and their leaders - Chief metrologists in terms of raising the level scientific research, improving product quality and social services population. Literally in all sectors, especially in aviation, space, radio electronics, instrumentation, nuclear and chemical engineering, the most important tasks and problems that put our country on the forefront of scientific and technological progress were solved at a faster pace.

However, it is also impossible to deny the fact that against the background of the implementation of "great plans and grandiose tasks", far from all enterprises showed attention to new metrological trends. At many enterprises there were "wise" managers who simply persistently did not notice the great benefits from the development of measuring equipment, the improvement of metrological support at the workplaces of science and production, not to mention the service sector of the population. Many metrological divisions were forced to be content with completely junk premises, experienced significant difficulties in staffing metrological sections necessary specialists, technical means and materials. The first wave of Chief Metrologists often had to fight with bureaucrats both at their enterprises and in their departments, who led enterprises, who did not always follow the directives of higher management bodies, which caused certain difficulties in improving metrological support at enterprises, in a number of cases, not only adversely affected the quality indicators of products, but also caused failures of individual units and serious accidents.

But that first wave of metrologists-enthusiasts nevertheless overcame all the difficulties and inertia of bureaucrats, as well as, in a number of cases, their insufficient awareness of the measurements of physical quantities. And we must give them their due, she won authority even among her own, sometimes not very understanding in metrology, enterprise managers, many of whom later very seriously relied on the already omniscient Chief Metrologists in matters of both product control and the safety of operation of various technical means and structures.

During the formation of metrological services, many Chief metrologists of enterprises felt supported in their practical work from the specialists of the State Standard, both the central office and individual institutions and territorial bodies. We must pay tribute to this system, so necessary to the state and surprisingly little paid, that it managed to concentrate in its composition a whole guard of outstanding specialists - scientists, engineers, technicians and good organizers of the State "Measuring business".

Unfortunately, given our general position with the economy in the country in recent years, it is very difficult, in general plan, to talk about some successes of the Chief metrologists of enterprises. Thank God that some of those specialists who started to create metrological services show patriotism for their metrological business and look forward to their successors in order to still have time to teach them something. In practice, the enterprises left, at best, 10-15% of specialists - metrologists, mechanics and equipment adjusters from the level of the early 90s. At many enterprises, the metrological services were simply liquidated, at others they were reduced, in some cases, the specialists of the metrological departments went into trade, commercial technical security services. A significant part of the personnel "gold metrological reserve", which was qualified for 15-20 years, was lost for industrial enterprises. And it is not even possible for enterprises reviving from stagnation to dream of replenishing the subdivisions of the metrological service at the expense of young people capable of mastering a wide range of equipment.

However, the specialists remaining at the enterprises - metrologists and instrumentation specialists of all directions do not have the right to lose heart, because they have all the hope that the past achievements in the field of scientific and industrial metrology in many industries can still be considered as a guide to the action of future metrologists and instrumentation specialists -enthusiasts. And, probably, the time for active actions is not far off, because a new "epoch of renaissance" is already visible at individual enterprises in a number of industries, the work on certification of products is being carried out more responsibly, the Gosstandart of Russia is carrying out quite serious work on introducing the experience of international activities in the field of quality system in the process of research, design, production, testing and operation of the created products (as well as in the field of consumption and services).

This work, grandiose in scale and complexity, aimed at achieving the competitiveness of products manufactured in our country, and which is an important basis for the socio-economic development of our society, in its essence is determined precisely by the high readiness for use and constant improvement of measuring equipment directly at each workplace of the enterprise. , where both products and their quality are formed. Any scientific and production task or problem, including social service to society, any issue of ensuring indicators of reliability, fail-safety, safety and reliability consumer properties of manufactured products is, first of all, a question of the adequacy of the volume (quantity, nomenclature, accuracy) of control and measuring (analytical) information. On the one hand, it paves the way in the process of searching for new, given by the time, opportunities for society, leads to the next steps of modern civilization, on the other hand, it stabilizes and consolidates what has already been achieved, including not only by issuing the necessary information, but also by regulating the required parameters in a production or other process. And this should be known not only to scientists, engineers and workers of all specialties who create manufactured products or any structures, but also to managers of enterprises of any profile or any form of ownership who plan funding for the metrological service and the development of control and measuring equipment. Managers of enterprises and economists should remember that normal, experienced specialists simply do not have excessive measuring information. The level, quality, including reliability indicators and consumer properties of products, entirely depend on the state of the organization of the metrological service and the state of measurements. As for material costs for measuring equipment, it has long been known that each ruble invested in measurements provides the enterprise with a 10-fold profit. Of course, perhaps not all entrepreneurs or heads of enterprises are interested in giving this ruble for the cause. Some think little about the reliability of their products, about good quality, about the shelf life and safety for the consumer, often hiding behind appearance or packaging, or no one knows where the certificate received, they tend to sell products as soon as possible, and there - "even though the grass does not grow." But the consumer will soon "bite" such a thrifty leader, and the company will face imminent bankruptcy.

It is probable that it is not a very rewarding task to teach the heads of enterprises how to measure, if they do not see it "point-blank". Far from everywhere, enterprises are headed by smart managers who rely on qualified and experienced specialists, in particular metrologists, who love their work, their team, and "sick" for the authority of their enterprise.

In recent years, many enterprises are headed by economists who have little understanding of technology, especially in the field of technical physics, which includes measuring technology, but they consider themselves good "marketers". In this case, it is very difficult for a real Chief Metrologist to work if the "economist" considers himself a "know-it-all". However, given the general problems with production in the country, the Chief Metrologist should not only have the "politeness of kings - accuracy", but also show, as they sometimes say, "political or diplomatic flexibility", educating their leaders in a "metrological" spirit, helping them to enter not only the "doors of the virtual economy", but also real world building quality indicators of labor processes. And, of course, the metrologists themselves need to more organically, systematically, with a reliable preparation of the regulatory framework, "enter" the tasks and problems of the enterprise, even if, to some extent, they are "adjacent" in nature, not to mention their functions.

However, if we assume that the metrological service can take its rightful place in market economy, including actively solving problems and problems in the "quality system", then in addition to preparing measurement processes, it simply has to expand and deepen its functions somewhat so as not to be "on the sidelines of the high road" of progress. But, first of all, we should talk about our "natural" traditional tasks, the solution of which should always be simply irreproachable; there should be no "white spots" in preparation for the implementation of any measurement processes at the enterprise, in particular, not only measuring instruments, but also measurement methods, primarily in terms of their certification, strictly exercising the functions of metrological supervision over the state of measurements. The possibility of appearance of reasons for criticism of the metrological service neither "from above" nor "from below" should be completely excluded.

The motto of the Chief Metrologist should be as follows - each measuring process has its own certified measurement technique and prepared equipment.

What tasks can, and most likely - should the Chief Metrologist think over in order to calmly and independently connect to the "quality system"?

Firstly, - this is the task of full coverage by the metrological service of the issues of scientific, technical, organizational and methodological maintenance of methods and means of high-quality instrumental control and analysis, the purpose of which is to obtain primary information for any need of the enterprise (product quality;

input control of raw materials, materials, hardware;

non-destructive testing, etc.). And of course, with the same motto, because often this kind of control is the basis of quality assurance.

Secondly, is the task of complex instrumental control and certification of test tools for all purposes (for test methods - only metrological examination).

Thirdly, is the task of instrumental control of the main operational and technical parameters of a unique technological and power equipment(special structures) that ensure its reliability and safety (based on the relevant regulatory and methodological documents), regardless of the systematic work on technical operation these funds from specialized services.

Fourth, is the task of metrological supervision over the state of the operational characteristics of the main collective Vehicle, carrying out passenger and road transportation in Russia, in order to ensure the reliability and safety of their use for freight and passenger transportation (metrological examination of operational and technical documentation, selective control checks of the condition of the main parameters and structural elements).

Fifth, is a metrological instrumental control of the output and critical parameters of especially important and complex products and structures at the stage after acceptance by the service technical control or during acceptance testing.

At sixth, is a periodic metrological control of the most important parameters of all types of production and environmentally hazardous objects, phenomena, including those tending to emergencies.

Seventh, - metrological maintenance of automation means (systems) (except for actuators with a power of over 100-200 W), bearing in mind that systems automatic control- a set of measuring transducers that are different in design and physical and technical basis.

Of course, all these (and maybe some other) tasks that are non-traditional for the subdivisions of the metrological service, if the latter should "more tightly" enter the "quality system" on a national scale, require careful analysis, elaboration from all points of view. On the one hand, it is possible that the new labor processes under consideration for the metrological service can give rise to impersonality in the production sector, on the other hand, it is possible to really sharply increase the responsibility and specialized technical services at the enterprise for the state of quality indicators at many "pain points" of production. And, of course, if the head of an enterprise is a person who understands something in terms of production quality, trouble-free operation, safety, reliability of communications, as well as the effectiveness of measuring equipment, then, of course, he will be happy with such a real quality system based on an end-to-end system of instrumental control of the entire production. But, at the same time, the Chief Metrologist will probably need to be respected to a much greater extent than at present. He may well be the deputy head of the enterprise for metrological support or the deputy chief engineer, etc. After all, they become metrologists only due to the intensive development of a very wide range of scientific and technical problems, related, in particular, to primary control and measuring information.

Perhaps, if the listed functions of the metrological service take root in enterprises, then, probably, as part of such a service it will be necessary to provide for special areas of production control, which, by the way, existed at individual enterprises before. It is possible that there will be many heads of metrological services; who will protest against the approach to production. But then you can ask the question - what will be the new participation of the metrological service in the quality system? If everything is the same - and again the "paper" system...? After all, this was already 30 years ago.

But, under all circumstances, the authority of the head of the enterprise in the quality system will be determined by his understanding of the problems of the metrological service, at the same time, the authority of the Chief Metrologist is the strict observance of the Law of the Russian Federation "On ensuring the uniformity of measurements" and the corresponding adherence to regulatory developments, directives of the State Standard of Russia system . Despite the fact that not all Chief Metrologists are satisfied with the Law, which probably needs to be discussed and clarified, there are many useful things in the materials of the State Standard, in particular, in the field of metrological supervision, when the head of an enterprise can give the Chief Metrologist the rights "Inspector for ensuring the uniformity of measurements at the enterprise". Of course, according to his status, the Chief Metrologist himself can restore the appropriate order at the enterprise, if the head of the enterprise supports the metrological service, but the emphasis in the "Inspector" part should not be in the recommendatory document.

At the same time, all these idle discussions about the active participation of the metrological service require a sober assessment of the state of uniformity of measurements today in the main industries of the country. It is probably very problematic. And to orient Chief Metrologists towards more effective work in new system quality is probably quite difficult. In addition, it can be observed that the State Standard of Russia is in no hurry to tighten State supervision over the state of measurements at enterprises - it relies on market levers, which supposedly should stabilize the situation. Indeed, if the consumer requires a certificate or accreditation of the metrological service in order to be more confident in the quality of the product that he is going to order, then it is assumed that the supplier will find the necessary means and put in place the perfect order in terms of metrological assurance, without which true quality is impossible. Of course, this is all correct. But such an economic engine, operating on the principle of natural economic selection, can run almost idle for many years. At the same time, enterprises, spending fairly cheap state resources, will still try with all their might to create products the way they will turn out, investing in the provision of consumer properties exactly as much as accidentally left from the wages of workers. And until a strong supplier appears against the backdrop of a shortage of high-quality products, such a "gray" state of production will leave its mark on strategic and social foundations country. But the real Chief Metrologist will not be able to endure such a sad situation for a long time. If he is not given the opportunity to restore order in the metrological service, in accordance with the Law, then he will go ... to the building manager. And such a case takes place after the liquidation of the metrological service at the Institute of Aviation Instrumentation.

But we can consider another option, without looking back in some case, at least temporarily, in our transitional period, to international documents. It is based on strict state supervision over the state of uniformity of measurements. Every enterprise, if it tries to create products, must definitely take care of the basis of quality, achieving precisely the advanced, reliable development of measuring technology, creating a strong metrological service, of course, within the real need, based on carefully thought-out production tasks. Then the new quality system will definitely bear fruit very quickly. The sufficiency of the volume of control and measuring information for all stages and stages of product creation will naturally, automatically bring up any manager who is a scumbag. If the head of the enterprise is not the latest lazy person or someone else like that, then he will immediately understand that not to use all the availability of this reliable information to produce better products - you just have to be "no one". Here, in this case, we can confidently talk about a quality system, where the main operational and informational figure should be the Chief Metrologist (possibly taking into account the above new functions for the metrological service), who prepares measurement processes with his specialists and performs individual control measurements, but also participating in the planning of control and measuring operations at the stage of research and development of products, starting with the source documents - an application for the creation of products, a technical proposal and a technical assignment. Only such close operational contact of metrologists with specific responsible persons for the areas of design and product research, enshrined in the relevant regulatory documents under the article of joint responsibility for the choice of initial data and methodological development of measurement processes. This professional community is also assumed in the development of ideology, principles, design, performance characteristics or consumer properties of products. A similar contact, but only with the technological apparatus, in terms of working out the manufacturing technology (production). At the same time, control and measurement information from ongoing tests is also in the field of view of metrologists, since they develop or certify the corresponding MVI under the influences specified by the designer and normalized for the product.

As a result, the participation of metrological services of enterprises in the new quality system could be really extremely effective if these services are organizational and supervised links of the national quality system, the only requirement for which is to ensure the "Uniformity of measurements in the system of indicators of product quality" (GSIPKP) . Of course, such a system can be developed, discussed at all levels of economic management and tested. The main thing in this system is that the actual state of measurements at the workplaces of enterprises should be adequate to the requirements of technical documentation issued by product developers. Naturally, all technical documentation should reflect the requirements for control and measurement processes (the availability of a methodology for their implementation), worked out in one way or another by metrologists. Chief metrologist - the person responsible for the validity of decisions made on the basis of the initial data of developers or researchers, carries out end-to-end metrological supervision over the implementation of any control and measurement (analytical) processes, participates in the consideration of the relevant information received, takes the necessary measures based on the results obtained, if the actual results of measurements (control , analysis) do not meet the requirements of developers, etc.

It is possible that in order to improve the status of the Chief Metrologist of an enterprise or even a person responsible for the state of measuring instruments, some independent structure - new appointments to these positions should be consistent with local authorities Gosstandart of Russia.

It must be emphasized once again that no quality system can really exist, at least in the coming years, if the state of measurements at enterprises does not meet the necessary requirements, capable of obtaining sufficient volumes of control and measuring (analytical) information, which requires the formation of a developed system of metrological support , creation of well-equipped sections of the metrological service. However, at present, all this can be done only if there is state supervision or wait until the still mythical economic categories "work". But the Chief Metrologists should not lose heart, look for ways to improve the metrological sections and educate new personnel of specialists - now this is their main task.

CHIEF METROLOGIST

1. General Provisions

1.1. This job description defines official duties, rights and responsibility of the person holding the position of chief metrologist.

1.2. The chief metrologist is appointed to a position or dismissed from work by order in agreement with the chief engineer.

1.3. The chief metrologist reports directly to the chief engineer.

1.4. The chief metrologist must know:

— Job description of the chief metrologist;

— Regulations on the metrology service;

— the federal law dated July 27, 2010 No. 190-FZ "On heat supply";

— Order of the Ministry of Energy of Russia dated March 24, 2003 No. 115 “On approval of the Rules for the technical operation of thermal power plants” (Registered in the Ministry of Justice of the Russian Federation on April 2, 2003 No. 4358);

— Order of the Ministry of Labor of Russia dated August 17, 2015 No. 551n “On approval of the Rules for labor protection during the operation of thermal power plants”;

— Order of the Ministry of Labor of Russia dated August 17, 2015 No. 552n “On approval of the Rules for labor protection when working with power tools and devices”;

- Rules for the commercial accounting of thermal energy, coolant, approved. Decree of the Government of the Russian Federation of November 18, 2013 No. 1034;

— Order of the Ministry of Labor of Russia dated July 24, 2013 No. 328n “On approval of the Rules for labor protection during the operation of electrical installations” (Registered in the Ministry of Justice of Russia on December 12, 2013 No. 30593);

— Instructions for providing first aid in case of accidents at the production site of RAO UES of Russia. Order of RAO "UES of Russia" dated 21.06.2007;

— Technical documentation for the main and auxiliary equipment installed in boiler rooms;

— Orders, orders and other internal local regulations;

— Information letters and other instructions from supervisors public services.

- Order of the Ministry of Energy of the Russian Federation dated 07/08/2002 No. 204 "Rules for the installation of electrical installations".

- Law of the Russian Federation of April 27, 1993 No. 4871-I "On ensuring the uniformity of measurements";

— Instructions for investigating and accounting for technological violations in the operation of power systems, power plants, boiler houses, electrical and heat networks (RD 153-34.0-20.801-00);

— Instructions for the prevention and elimination of accidents in the electrical part of power systems (SO 15334.20.561-2003);

— The scope and standards of electrical equipment testing (SO 34.45-51.300-97);

- Federal Law of November 23, 2009 N 261-FZ (as amended on July 13, 2015) "On Energy Saving and Increasing energy efficiency and on amendments to certain legislative acts Russian Federation»;

— Federal Law of December 21, 1994 No. 69-FZ “On Fire Safety”;

— Federal Law No. 123-FZ dated July 22, 2008 “Technical Regulations on Fire Safety Requirements”;

— Resolution of the Government of the Russian Federation No. 390 dated April 25, 2012 (as amended on March 6, 2015) “On the fire regime” (together with the “Rules for the fire regime in the Russian Federation”);

- Order of the Ministry of Emergency Situations of the Russian Federation of December 12, 2007 No. 645 (as amended on June 22, 2010) “On approval of the Fire Safety Standards “Training fire safety measures for employees of organizations” (Registered in the Ministry of Justice of the Russian Federation on January 21, 2008 No. 10938);

— Labor Code Russian Federation dated December 30, 2001 No. 197-FZ;

— Federal Law No. 426-FZ dated December 28, 2013 “On special evaluation working conditions”;

— Federal Law No. 125-FZ dated July 24, 1998 “On Mandatory social insurance from accidents at work and occupational diseases;

- Order of the Ministry of Health and Social Development of Russia dated June 1, 2009 No. 290n (as amended on January 12, 2015) “On approval of the Intersectoral Rules for Providing Workers special clothing, special footwear and other personal protective equipment” (Registered in the Ministry of Justice of Russia on September 10, 2009 No. 14742);

— Order of Rostekhnadzor No. 542 dated November 15, 2013 “On Approval of Federal Norms and Rules in the Field of Industrial Safety “Safety Rules for Gas Distribution and Gas Consumption Networks”. (Registered in the Ministry of Justice of Russia on December 31, 2013 No. 30929);

— Order of Rostekhnadzor dated January 29, 2007 No. 37 (as amended on December 6, 2013) “On the procedure for training and certification of employees of organizations supervised Federal Service on Environmental, Technological and Nuclear Supervision" (together with the "Regulations on the organization of work on the training and certification of specialists from organizations supervised by the Federal Service for Environmental, Technological and Nuclear Supervision", "Regulations on the organization of training and testing the knowledge of workers' organizations supervised by the Federal Service for Environmental, Technological and Nuclear Supervision”) (Registered in the Ministry of Justice of Russia on March 22, 2007 No. 9133);

- Order No. 302n dated 12.04.2011. Ministry of Health and social development Russian Federation "On approval of lists of harmful and (or) dangerous production factors and work, during the performance of which preliminary and periodic medical examinations (examinations) are carried out, and the procedure for conducting mandatory preliminary and periodic medical examinations(examinations) of workers engaged in hard work and work with harmful and (or) dangerous working conditions”;

– Methodological and regulatory materials on the metrological support of production;

— Organization of metrological support of production;

— Standards and others regulations on metrological certification of products, operation, repair, adjustment, verification, adjustment and storage of measuring instruments;

— Technical requirements applied to the products manufactured by the enterprise, the technology of its production;

— Specifications, design features, purpose and principles of operation of measuring instruments, technology for their repair;

— Methods for performing measurements;

— The procedure for attestation and certification of products;

— Advanced domestic and foreign experience in the field of metrological control and production support;

– Basic requirements for the organization of labor in the design;

— Order of definition economic efficiency introduction of new methods and measuring instruments;

1.5. During the absence of the Chief Metrologist, his duties are performed by a person appointed by the Order in the prescribed manner.

1.6. A person with a higher (technical) education and work experience in the specialty of at least 3 years is appointed to the position of Chief Metrologist;

1.7. The primary appointment of a newly appointed chief metrologist is carried out no later than one month after appointment to the position.

1.8. The frequency of certification and verification of knowledge of the chief metrologist is established by the relevant regulations RF.

2. Job responsibilities

The Chief Metrologist performs the following duties:

2.1. Organizes work on metrological support for the development, production, testing and operation of products manufactured by the enterprise.

2.2. Supervises the preparation of projects and plans for the introduction of new measuring equipment, organizational and technical measures to improve production efficiency, improve metrological support, means and methods of measurement, control and testing.

2.3. Ensures the compilation of local verification schemes, the establishment of the optimal frequency and the development of calendar schedules for verification of measuring instruments.

2.4. Leads the work on carrying out metrological examination of design and other technical documentation developed at the enterprise, as well as coming from other enterprises and organizations.

2.5. Participates in ongoing research on the automation of production processes related to the use of measuring instruments, in the work to determine the needs of the enterprise for these means.

2.6. Ensures the introduction of modern methods and measuring instruments, as well as the performance of work on the assessment of measurement errors.

2.7. Organizes work on the analysis of the state of metrological support, carrying out metrological certification of non-standardized measuring instruments, development, coordination and approval of methods, instructions and other regulatory and technical documentation for their verification, as well as certification of measuring instruments after restoration, repair, verification.

2.8. Carries out control over the equipment of the technological process with all the measuring instruments provided for by the regulations, the compliance of the measuring instruments and methods used in the divisions of the enterprise with the requirements for compliance with the specified production modes and product quality.

2.9. Issues instructions aimed at preventing, stopping or eliminating violations of metrological rules and norms in the metering stations for thermal energy, the consumer's coolant.

2.10. Issues instructions aimed at preventing, stopping or eliminating violations of metrological rules and standards at heat supply sources.

2.11. Organizes the preparation of technical specifications for the design and development of special-purpose measuring instruments.

2.12. Ensures the completion of the exchange fund of measuring instruments, testing and control, storage and comparison in the prescribed manner of working standards, repair and maintenance of samples of measuring instruments in proper condition.

2.13. Promotes the implementation of state and industry standards, enterprise standards and other normative and technical documentation regulating measurement accuracy standards, methods and means of verification.

2.14. Supervises the work on the preparation of the established reporting and its submission to the bodies of the state metrological service.

2.15. Organizes work to improve the skills of workers of the metrological service, in agreement with the employer.

2.16. Performs work in the field of labor protection and ensuring the fire regime. Creates healthy and safe working conditions, normal conditions for rest. Provides a high culture of production, proper sanitary condition service premises.

2.17. Fulfills the instructions of the labor protection service, State supervision services in a timely manner.

2.18. Manages the production and economic activities of the service.

2.19. Provides timely reporting on the production and economic activities of the service.

2.20. Conducts work with personnel in accordance with regulatory and legal acts.

2.21. Complies with the requirements of the rules on labor protection, fire and industrial safety.

3. Rights

In the course of his activities, the Chief Metrologist has the right to:

3.1. Act on behalf of the metrology service, represent the interests of the enterprise in relations with the structural divisions of the enterprise, state metrological control and supervision bodies, and other state authorities on issues of metrological support of production.

3.2. Make proposals to the head of the enterprise on the conclusion of agreements on the lease of unique measuring instruments and test equipment for calibration and other metrological work, as well as agreements on the involvement of third-party specialists in the metrological examination of documentation and metrological certification and the introduction of measurement methods.

3.3. Ask for assistance from the heads of structural divisions and independent specialists in providing the information necessary to perform work on metrological control and metrological support of production.

3.4. Participate in the preparation of draft orders, instructions, instructions on the issues of metrological support of production.

3.5. Give recommendations to the heads of structural divisions of the enterprise on issues of metrological control and production support.

3.6. Submit proposals in accordance with the established procedure on bringing to responsibility officials guilty of violating the rules for the use of measuring instruments, the procedure for metrological support of production.

3.8. Submit for consideration by the head of the enterprise:

3.8.1. Representations about the appointment, transfer and dismissal of subordinate employees.

3.8.2. Proposals to encourage distinguished employees, to bring to material and disciplinary liability violators of production and labor discipline.

3.9. Approval and sign documents within their competence.

3.10. Independently conduct correspondence with structural divisions of the organization, as well as other organizations on issues within its competence and not requiring the participation of the head of the enterprise.

4. Responsibility

The Chief Metrologist is responsible for:

4.1. Untimely and poor-quality performance of their duties, provided for by the job description of the chief metrologist.

4.2. Non-fulfillment of work plans, its volumes, deadlines and quality.

4.3. The results and effectiveness of their production activities.

4.4. Reliability of information about the results of the work carried out.

4.5. Failure to comply with orders, directives and orders of management.

4.6. Failure to comply with the rules of internal labor regulations and labor discipline.

4.7. Violation of the rules on, and, as well as other regulatory and legal acts that pose a threat to the activities of the enterprise and its employees.

4.8. The quality and timeliness of the tasks and functions assigned by the job description to the chief metrologist.

5. Relationships

When fulfilling their functional duties The chief metrologist carries out the following relationships:

5.1. With chief engineer and director

Gets:

- tasks or orders for the performance of work.

Transmits:

— information in the form of acts and reports with conclusions and proposals;

— schedules and scope of work;

- information about the work done;

- reporting documentation.

5.2. With Head of HR

Gets:

- signed vacation schedules;

- information about employees of the service.

Transmits:

— office notes on employees of the enterprise called to work for production needs;

- sick leave records of staff.

5.3. with supply department

Gets:

- tools, personal protective equipment from the warehouse, according to the submitted applications.

Transmits:

- applications for essential tool, personal protective equipment approved by the chief engineer.

5.4. With third parties (consumer representatives, contractors)

Gets:

— technical documentation;

- applications for checking the operation of metering devices;

- reports on the consumption of thermal energy, coolant to analyze the correct operation of metering devices.

Transmits:

- certificates of admission;

— acts of defects;

- technical documentation.

5.5. with sales department

Gets:

- information on the availability of heating and hot water metering devices put into operation by consumers;

Transmits:

- acts of admission or prohibition;

- reports on the consumption of thermal energy, coolant.

5.6. with legal department

Gets:

— information about concluded agreements (contracts);

Transmits:

- information for the conclusion of agreements (contracts) for the maintenance of metering devices;

— information on the transfer of technical documentation.

5.7. With production and technical department

Gets:

— information on connection schemes for heat supply facilities;

— information about sources of heat supply;

— specifications And project documentation on connections of metering stations.

Transmits:

- technical documentation.

5.8. With the service of adjustment, testing and modes

Gets:

- information on the detection of faults in the measurement of heat energy metering devices, coolant;

— information on the detection of violations in the internal heat supply system and hot water supply and on heat supply sources;

— information about connected heat supply facilities;

- acts and regulations based on the results of the survey of heat consumption systems;

- instrumentation for verification.

Transmits:

— reports on the consumption of thermal energy, coolant;

- information on the availability of metering devices at consumers, at sources of heat supply;

— certified instrumentation;

- information on the elimination of violations in the operation of metering devices at the consumer and at heat supply sources.

5.9. With operational dispatch service

Gets:

- information about disconnected and connected power supply facilities;

— information on connection and disconnection of thermal energy consumers in connection with the beginning of the heating season and at its end;

— information on the timing of planned shutdowns of heat sources;

— information on interruptions in the supply of thermal energy to consumers as a result of emergencies;

— information on switching heat supply sources;

- information about violations in the operation of metering devices at heat supply sources;

- daily schedule of the operation of heat networks and heat sources based on the weather forecast for the next day, issued by the meteorological service.

Transmits:

— reports on the consumption of thermal energy, coolant;

5.10. With accounting

Gets:

- pay slips wages;

- material report;

— information on service contracts and payment for them;

- information on debts on payment for servicing consumer metering devices.

Transmits:

- write-offs material assets;

- invoices for the internal movement of material;

- information on the work performed under the contracts;

- other documents on request.

5.11. With the service of the chief power engineer

Gets:

- instrumentation for verification;

Transmits:

— trusted instrumentation;

- information on the elimination of violations in the operation of metering devices at heat supply sources.

5.12. With the heads of boiler houses

Gets:

— Necessary operational information on the state of equipment for adjustment work of metering devices at heat supply sources;

- information about violations in the operation of metering devices at heat supply sources.

Transmits:

- information on the operation of metering devices at heat supply sources;

- information on the elimination of violations in the operation of metering devices at heat supply sources.

5.13. With the labor protection service

Gets:

— information on current and newly introduced normative and legal acts on labor protection, industrial and fire safety;

— regulatory and legal acts on labor protection, industrial and fire safety;

— information letters, operational instructions and other materials of controlling public services in the field of labor protection, industrial and fire safety;

— guiding documents (orders, orders, regulations…);

— the standard for providing personnel with personal protective equipment;

- instructions, measures to eliminate the comments identified during inspections of workplaces;

— measures to improve working conditions;

- schedules for checking the knowledge of managers;

— information about fires and injuries;

— directive documents regulating the relationship to ensure labor safety.

Transmits:

— reports on the implementation of instructions;

— reports on the implementation of orders, directive documents and other measures to improve the reliability of equipment operation, improve the state of labor protection, fire and industrial safety;

- acts, schedules, programs, lists, etc.;

— explanatory notes on issues of violation of the requirements of regulatory and legal acts on labor protection, industrial and fire safety.

 

It might be useful to read: